Category Archives for "Blog"

How to Find the Best Kitchen Sink

Not everyone is concerned about finding and buying the best kitchen sink. When you were a kid, you most likely didn’t really think about your kitchen sink at all. It’s just a place where you placed dirty plates and glasses. It’s where the water goes when you washed your hands. It’s just there, and it doesn’t seem important at all.

But when you get older, you get a special appreciation of what a good sink offers. Can you imagine not having a kitchen sink at all? Without it, you’d have to go outside to wash your hands and your fruits and vegetables. You won’t be able to get a quick spray on your plates and glasses.

But not all kitchen sinks are the same. They have different areas and depths, and they can be made from different materials. They can even have different extra features. Not all kitchen sinks can suit your particular needs. Even its look will affect the overall kitchen interior design. All these reasons should convince you to take some time aside to figure out just what the best kitchen sink is for you.

To help with that, we can help point out the considerations you have to factor in when you choose a kitchen sink. We also offer best kitchen sink reviews, along with some other information that can help you decide which one suits your needs.

What to Look For when Buying a Kitchen Sink

To help you decide on the best kitchen sink for you, these factors should be kept in mind:

  • The number of basins. This is perhaps one of the more basic factors you need to think about. How many basins do you really need? You can have a basic single sink with a faucet, but you can have 2 basins. With these, you can even make do with a single faucet if that faucet can swivel. Some sinks have 3 basins, but then for these most part these are commercial grade kitchen sinks typically used for restaurants.
  • The dimensions. Just how large do you want your sink to be? Large sinks can pre to be more convenient, but smaller ones are more accessible and can fit better in a small kitchen. You also need to think about the depth of the sink.
  • The type. There are actually many different types of kitchen sinks. There’s the farmhouse sink, which offers a vintage vibe. You have the undermount sink that hangs from a countertop instead of being supported by the countertop. You may see bar sinks that can function as a small sink for entertaining areas or as a secondary sink in your kitchen. Sinks can have square edges or rounded edges. Then there are the vessel sinks that are basically modern versions of the wash basin.
  • The materials used. Porcelain is perhaps the most common as the sinks made from porcelain are durable and pretty. Other kitchen sinks feature stainless steel. This is quite durable, though they do show water spots and they may need a bit of maintenance. Other materials include copper, granite, fireclay, acrylic, resins, and natural stone. Each material has its own benefits and drawbacks.
  • Removable inserts. These can be racks for dishes, utensils, and dishcloths. They can be very convenient, though they add to the price.

Product Reviews

With the important factors in mind, just which kitchen sinks are the best? You can start your search with these excellent options:

Kraus KHU100-30

When you’re looking for a kitchen sink, it’s good to start your search with a reputable brand. That means you should really take a look at the Kraus kitchen sink lineup, as this brand is renowned for its excellent products.

This model is actually available in 26-inch and 28-inch models, but your best bet is to just go for the 30-inch model instead. Whether you’re upgrading your current kitchen countertop or you’re building a new home, this sink will work very well in your kitchen.

Since this is deep and large, you won’t have any trouble putting in your largest kitchen ware. Even a 12-quart stockpot will fit right in. a large party won’t be a problem either, since it can fit up to 30 dinner plates without going over the basin. The depth of the basin also helps in containing the splashing, so your apron won’t have to do heavy duty in protecting your outfit.

This sink may look deceptively simple, but it’s actually been handcrafted to ensure quality. It uses heavy duty 16-gauge stainless steel. This is actually T304 stainless steel with just enough carbon that properly balances strength, corrosion resistance, and ductility. It’s extremely durable and can resist having dents either. It also comes with a limited lifetime guarantee.

Now you may think that the kitchen can get noisy with the plates and the stainless steel in constant contact, but that’s not so. That’s because Kraus put in what they call their NoiseDefend, which involves having more than 80% of the base of the sink covered by super-thick rubber. The rubber helps to absorb the sound so the resulting noise is considerably reduced.

The drainage isn’t a problem either. Its design has been optimized for highly efficient drainage. Water doesn’t pool in the bottom of the basin as there are channel grooves in the sink.

This comes with plenty of accessories, and they include a 3-piece basket strainer, a bottom grid, and a dish towel made from 100% cotton. You even get a utility bag for all these stuff. These accessories also include the installation instructions and template, along with the mounting hardware and a user’s manual.

  • It’s been handcrafted.
  • It’s made with durable stainless steel.
  • It’s large and deep.
  • It’s quiet.
  • Standing water doesn’t pool at the bottom.
  • It comes with lots of accessories.
  • Installing it is easy.
  • It’s guaranteed for life.

Zuhne Modena Undermount Deep Single Bowl 32 x 19

The Zuhne Modena Undermount Kitchen Sink actually comes in 8 different sizes, but the 32 x 19-inch is the largest and deepest. If you have the space for such a size and you tend to wash large pots and lots of produce, then you may want to go with this humungous size.

This is one of the most popular kitchen sinks in the world, and it is extremely well-regarded by just about everyone who’s bought it. This largest size is certainly spacious, as the internal space measures 30 by 17 by 10 inches. The manual and the CAD are all available online, and you don’t even have to buy the kitchen sink to get them.

It’s not just about the size, of course. It’s how people use it, and they find that it works very well indeed. It’s simply a solid piece of work, and to confirm its durability it also comes with a solid guarantee. The solid stainless steel used here is resistant to dents and it is surgical-grade. It complies with US and Canadian codes and it uses nontoxic components.

Noise may be an issue with a sink like this, but that’s not true for this particular model either. It uses insulation technology that makes it among the quietest (if not the quietest) sink in the market today. It uses pads that are twice the thickness of the noise-proofing pads used by other brands, plus they’re on 90% of the sink’s outer body. This insulation even helps in protecting the sink cabinet from condensate damage.

Finally, you get the accessories you need with your kitchen sink. For the installation you get the manual, the cutout template, and mounting clips. It’s accompanied by a 3-piece strainer, along with a bottom grid that prevents scratches for the surface of the sink. They even threw in an extremely absorbent towel.

  • It’s perhaps the quietest sink in the market.
  • It’s huge.
  • It uses premium surgical-grade stainless steel.
  • It’s easy enough to install with the necessary accessories as part of the purchase.

Kraus KHU100-32

We’ve already mentioned the Kraus KHU100-30 earlier on this article, right? Now this has the very same features, except for the fact that it’s 32 inches wide. That’s the main difference, and it can be the crucial difference.

What if you work with large pots and you need to wash them on the kitchen sink? If that’s the case, wouldn’t you want some space to enable you to put the pit in the basin more easily? The larger space also accommodates more of the smaller stuff like fruits and veggies if you want to clean them in the sink.

You can clean those veggies in the basin because it uses a commercial-grade finish. Again, this also has as the 16-gauge T304 steel as material for the body. It has a very deep basin with NoiseDefend technology, and it comes with a lifetime guarantee.

You also get the 3-piece basket strainer, the bottom grid, the cotton dish towel, and a utility bag for all these accessories. The installation shouldn’t trouble your plumber as it comes with the mounting hardware along with the installation template and instructions.

  • It uses durable and dent-resistant stainless steel with a commercial-grade finish.
  • It’s quiet.
  • The basin is very spacious.
  • Drainage goes smoothly.
  • It’s easy to install and maintain.
  • You’ll have no worries about the durability as it’s guaranteed for a lifetime of use.

Kraus KBU14 31-½ inch Undermount Single Bowl 16-gauge Stainless Steel Kitchen Sink

It may not be too easy to differentiate between the Kraus KHU and the Kraus KBU kitchen sinks, because they tend to have the same tech and features. However, a closer look shows you that this model has rounded corners, so it seems to have a nicer aesthetic. It makes cleaning a bit easier as well.

It’s also easy to clean because of the commercial-grade satin finish. For many, it does look nice and elegant, at least for a sink.

There’s also no doubt that this is a really roomy basin. The 31.5-inch model offers the most space in the KBU lineup, with a 10-depth to match the nice wide dimensions. You cans tack up to 24 dinner plates inside the basin.

Kraus does like to incorporate their topnotch technology into their premium kitchen sinks. That’s why its features should by now be familiar to you if you’ve read the other Kraus reviews on this article. There’s the use of the T304 stainless steel, soundproofing technology, and the lifetime assurance. There’s the stainless steel grid to prevent scratching on the basin surface, and the stainless steel basket strainer that keeps debris from getting into your drainpipe.

  • It looks great.
  • It’s easy to clean and install.
  • It’s quiet.
  • You’re assured that it will be replaced if it doesn’t work.
  • It uses premium T304 stainless steel.
  • You get a lot of extras.

Kraus KBU22 32 inch Undermount 50/50 Double Bowl

Now we come to something different. The main difference between this mode and the others we’ve mentioned earlier is that this comes with a double bowl. They both have the same size, so you can use either one.

Having a double sink makes things go a lot faster when you do lots of tasks at the kitchen sink. You can rinse more fruits and veggies at once, and you have more space for dinner plates.

The double sink also gets you double the accessories. This means you have 2 grids to protect each basin, and you have 2 basket strainers to keep the drainpipe from clogging.

Kraus again put in all their excellent features into this model. You have the commercial-grade finish that’s easy to clean, and you have the rounded edges for each basin. The stainless steel used is tough and durable, plus it resists corrosion. You get the padding that absorbs the sounds so that putting stuff inside the basin doesn’t cause an awful ruckus. There’s also the Kraus limited lifetime guarantee.

  • You have 2 basins to work with.
  • It’s easy to clean.
  • You get bottom grids and drainpipe protection.
  • The steel is tough, and it won’t corrode easily.
  • There’s the Kraus guarantee.

Kraus KHU101-23 23 inch Undermount

Do you really need a large sink? It’s a serious question, especially when you just use the sink and faucet to mainly wash your hands and produce. You also may just need a place to store the dirty dishes. In fact, you may not even have a large enough kitchen countertop to accommodate a huge kitchen sink.

So what do you do? Well, you just get a small sink instead. It’s not that this is overly small either. It measures 23 inches long and 18 inches wide, and it’s 10 inches deep. That’s still a deep basin, with enough space for regular pots and pans along with plates.

Just because it’s small doesn’t mean that Kraus skimped on the quality either. This is still part of the KHU series, and it’s fantastic. It uses the premium-grade T304 16-gauge stainless steel that’s durable and scratch resistant. The premium satin finish looks great, and it’s resistant to dents.

You won’t have to worry about noisy kitchen sink tasks. You have especially thick rubber pads absorbing the sound and there’s Stone Guard undercoating too. The pads cover 80% of the kitchen sink base. It’s been designed for super-efficient drainage. You have the various accessories like the strainer and the bottom grid, and the guarantee is terrific.

  • It’s not too small, so it’s just right for some.
  • The commercial grade satin finish is easy to clean.
  • Drainage runs smoothly.
  • You get freebies like the bottom grid and the strainer.
  • It’s very quiet.
  • You’re sure it’ll work for life.

Kraus KBU12 23 inch

Cleaning the sink around the sides is easier when you have rounded edges, isn’t it? That’s what you get when you get the Kraus KBU12 23 inch. The KBU series comes with rounded edges, and aside from the easier cleaning it also looks somewhat more charming than just regular square edges.

It is 23 inches long and 17.5 inches wide, and the depth is at a good 9 inches. It looks great, and its “not so big” size doesn’t mean that it’s inferior. It still has the premium qualities of the other KBU series kitchen sinks.

You have the T304 stainless steel, the soundproofing, the extra accessories like the bottom grid and the strainer, and the terrific guarantee. It may be smaller than usual, but it’s the opposite of terrible.

  • It looks good with the undermount clean look and satin finish.
  • The rounded edges make it easier to clean.
  • It uses tough stainless steel.
  • It’s not noisy at all.
  • It comes with a cast-iron assurance that it’ll be replaced if something goes wrong.

Kraus KHU103-33 33 inch Undermount

Lengthwise, this is the longest of the KHU series featured here on this list. But the main difference here is that this offers 2 basins. It also comes with a 60-40 basin configuration. This means that one basin is 1.5 times bigger than the smaller one. Both basins are 17 inches wide, but the bigger one is 16.9 inches long while the other is 12.9 inches long.

Again, this offers you the other outstanding features of the KHU series. It’s made with the vaunted T-3-4 stainless steel, and it’s even been handcrafted. The finish adds to the resistance against rust and corrosion. It’s quiet to work with it as rubber pads at the base dampen the sound of your plates hitting the sink bottom.

That sink bottom has grooves to channel the water more efficiently so you don’t have pooling water at the bottom. You also get strainers and bottom grids for the 2 basins, and there’s a great guarantee.

  • It’s very durable with resistance to rust and corrosion.
  • It won’t make clanking noises as you put glasses in the basin.
  • It’s easy to clean.
  • It looks great.
  • You get accessories.
  • There’s a limited lifetime assurance of quality.

Ruvati RVM4350 Undermount

Just in case you think this list is made up entirely of Kraus kitchen sinks, you get this RVM4350 Undermount from Ruvati. This offers you 2 basins, and that’s not the only unique aspect to this kitchen sink.

The divider between the basins is 3 inches lower, so you have greater clearance space when you’re moving your plates from one basin to another. The basins each measure 14.4 by 17 inches, with a depth of 8.5 inches. The drain measures 3.5 inches so that’s good for any garbage disposal.

It looks great, as the rim is brushed and finished just like the sink interior. This lets you install it as an undermount or flushmount. The brushed satin finish is artisan-grade, and it’s easy to clean. That’s especially true with the rounded edges.

The soundproofing is quite ample. That’s because you have rubber pads at the base of the sink and around all its sides. The pads also help in providing thermal insulation against condensation.

You get the cutout template and mounting brackets to make the installation easier. Other extras include rinse grids for the bottom and basket strainers too. The sink meets US and Canadian plumbing standards, and the durability is reliable. It comes with a lifetime guarantee.

Kraus KHF200-33 33-inch Farmhouse Apron

Yes, we’re ending this list with another Kraus kitchen sink. This isn’t like the other Kraus sinks mentioned before. This comes with a farmhouse design, so even with the stainless steel its configuration and shape makes it more apt for rustic or antique stately homes. It’s even been handcrafted.

Aside from the looks of it, there’s also the size of this particular model. It measures 32⅞ inches long and 20¾ inches wide. It offers a deep basin at 10 inches. It can be installed in 3 ways.

This also comes with all the other fantastic innovations and advanced features that built up the Kraus popularity and reputation. It uses the premium T-304 16-gauge stainless steel that’s known for its durability. You have superior noise proofing and rounded edges for easier cleaning. Drainage is smoother because of the grooves at the bottom. The finish looks fantastic.

  • It’s big enough to contain even your largest pans and pots.
  • Its durability is unquestioned.
  • It’s easy to clean.
  • It looks great, especially for rustic homes.
  • There are several ways to install it.
  • You get optimal drainage.
  • It’s very quiet.

What Are the Top Kitchen Sink Brands?

It helps when you limit your options to the best kitchen sink brands, as their wares tend to be of higher quality. Some of the brands you should consider include:

  • Kraus. No list of kitchen sink brands will be complete without a mention of Kraus, so let’s just mention it first. They offer a very diverse range of kitchen sinks that should fit many needs and kitchen aesthetics. They tend to combine numerous functions with stylish looks, and their sinks can last for a very long time. They even often come with a terrific proof of quality, while the reputation of their customer support is topnotch.
  • Zuhne. This brand produces many types of sinks, from single and 2-basin sinks to economy sinks. They use food-grade or surgical solid stainless steel in their sinks, and they also have a lifetime guarantee on all their products. Despite the Zuhnë name, they’re actually based in Houston, Texas.
  • Ruvati. This brand is based in the US and it has manufacturing facilities here, and also in Spain and China. It’s a new brand as it was lunched just recently in 2009, and they’re quite conscious about not harming the environment. They add eco-friendly features to their sinks, such as using 80% recycled stainless steel for their stainless steel sinks. The typical stainless steel product uses only 60% recycled steel. They’ve also earned an A+ rating from the Better Business Bureau.


Let’s tackle a few questions about kitchen sinks:

How are kitchen sinks installed?

The best and simplest answer is that you call a plumber who does it for you. In fact, you should consult with your plumber first as they can advise you on which sinks can fit in best with your countertop.

Of course, you can DIY even though that carries a risk that you’d DIY incorrectly. Plenty of videos can be found online which can demonstrate how to install your particular kitchen sink. Many of the top brands come with the appropriate mounting hardware, and they also have precise installation instructions.

Why have porcelain kitchen sinks remain popular?

That’s because it’s traditional, and many people like the familiar look of porcelain sinks. Also, the material is durable, and it can come in many designs and colors. The base material of porcelain is glass, after all.

However, there have been many people looking for alternative materials because porcelain can chip as it contains glass material. Also, porcelain can eventually develop those unsightly black marks.

So what has become the most popular alternative?

Many people who have made the switch from porcelain kitchen sinks have shown a preference for stainless steel. Now this is extremely durable, and it’s also easy to shape. That means you can have it designed to avoid pools of water at the bottom.

On the other hand, it can be annoyingly noisy when you put pots and plates in the basin. You may also have to constantly wipe it down to get rid of water spots.

What about copper?

Some premium kitchen sinks are made of copper. They’re a bit more expensive, but then they’re uncommon and they offer several advantages. Copper doesn’t rust. Also, it’s been found that most bacteria just can’t survive for long on a copper surface.

However, you have to be ready for the color of the copper to change over time. Copper is extremely reactive, so eventually it will develop a patina. You can end up with some dark or green spots eventually. Polishing the copper can prevent this issue, but then your polish inhibits the anti-microbial property of the copper surface.

Are granite and granite composite materials good for kitchen sinks?

For many, granite composite materials can actually be a superb alternative. A high quality granite composite sink is more durable than the standard porcelain sink. It can be made to be resistant to chips and scratches.

This material also comes with a somewhat speckled design, and that works to camouflage any water spots. It’s also easy and cheap to maintain a sink like this, as most of the time you just need a mild cleanser. Just don’t to clean it regularly, as hard tap water can contain minerals and dyes that can react with the copper to result in stains.

Are there acrylic kitchen sinks?

Indeed there are, and they’re actually reasonably priced for the most part. They’re also lightweight and they often come with a nice finish. The smooth surface can be sanded in case it gets scratched.

On the other this material doesn’t always react well to hot water.

What about natural stone sinks?

Yes, they’re available as well. They fit in nicely with period homes and rustic houses. They’re often gorgeous, and their natural state offers a timeless vibe. The usual stone is typically soapstone.

This can be expensive though, and you need special cleaning agents for the stone. Using the wrong cleaning agent can mar the stone. In addition, the stone can be damaged by chips.

Are stone sinks the same as “solid surface” sinks?

No, they’re different. Solid surface refers to the use of minerals and resins. It’\s very durable, and they can be repaired. If it gets scratched, you can just sand and polish the stone.

However, fixing most damages to the solid surface usually will require the attention of a professional, sot the repair bill can get costly.

Final Words

You have to think about your kitchen sink if you’re building or upgrading to a new kitchen. You have to think about how it looks and how large and deep it has to be. You need to consider its durability, and the noise it will create when you’re putting kitchenware in. You also should check out how easy it is to clean.

Check out our list of recommendations, and you’ll find that your search for the best kitchen sink will be off to a very good start. Pick one that suits your needs, and you’ll have a much better time in the kitchen.

How to Use a Paring Knife?

Many of us users have been familiar to paring knives, since they are one of the most effective kitchen utensils. But if you want to do something with it, don’t start with it before you get done with this article. Because we have talked about some of the crucial tips that makes it easier to work with paring knives.

Let’s start with the core of this article-

Some Common Uses of paring Knives

At this section of the content, we’ll learn about some of the most common uses of paring knives that are mostly used in kitchen. It includes slicing veggies fruits, peeling skins of fruits or vegetables, peeling thick skins and lastly, using the tip of the knife as a sharp and pointy cutting tool.

In the section below, let’s discuss something about all these four uses-

  1. Slicing Jobs

    One of the most common work that slicing knives do is to slice the fruits ang vegetables. You can slice fruits that are easy to slice, you can also go with tough fruits like sweet potatoes or many more.

  2. Peeling the Skins of Fruits and Veggies

    Another common but important task is to peel fruits of fruits and vegetables. Soft fruits and vegetables like apples and potatoes can be the ideal item on this. Paring knives has a sharp edge can make this task fast and effective.

  3. Peeling Fruits with Thick Skins

    When it comes to peel fruits with thicker skins, paring knives can be also effective. You can easily wrap out the thick skins out of these fruits.

  4. Doing Single-point Cutting Jobs with the Tip

    The tip of paring knives is quite pointy and that enables it to do any kind of job that a blade can do. It includes all sort of marking up. Also, fruits like strawberries, where you need to twist the top to remove the hull, this can be an effective tool.

How to Use a Paring Knife- Step by Step

Now as we have known the uses of paring knife in daily kitchen life, lets go on the detailed guide on how to use it. Although, it’s a day to day matter for an expert homemaker to use a knife, but in case of paring knives, I think there are some particular tricks.

Let’s take you through the step by step guide of using a paring knife-

Step 1: Hold the Fruit or Vegetable with One Hand. Make sure you gave kept the part open. I am talking about the part that you start the cutting job with.

Step 2: Now take the paring knife with another hand and place the sharp edge of the knife on the fruit or vegetable. Make sure your other hand’s finger are safe enough not to be cut.

Step 3: Wrap the knife around the entire perimeter of the fruit. If it’s a vegetable (which is not round) than start with each side of it. It will make one side of the fruit wrapped out of skin. Do the same process for the next slice.

Step 4: Rest your hands on the other side of the blade. Not take an attempt to make a tiny amount of inclusion from the side of the fruit’s skin. It will cut down the skin and path.

Step 5: Now rotate the knife through the sideways. As the cutting process is almost done, peel away the skin from the body.

A Few tips Before We Finish

Before we finish todays discussion, lets go through some tips that might be in help to keep you safe throughout the process-

  1. Make sure you keep the knife edges as sharp as possible
  2. Make sure you keep the paring knives safe and sound. As their knives are small, they are likely t be lost in sinks and drawers.

How to Unclog a Shower Drain with Standing Water?

If you find that, your shower is not draining, it can be very frustrating. Shower drains can get clogged time to time. The minerals from hard water, soap, etc. block the easy drainage of your shower drain sometimes. At that time, it becomes necessary to unclog it as early as possible. You can always avoid calling a plumber for unclogging your shower drain if you can do it by yourself. The point is unclogging the drain of the shower isn’t that difficult as people often think.

The huge majority of shower drain clogging problem you can solve by your own easily. For that, you just have to follow some fair and simple methods and also require some basic tools. So, if you are going to do it by yourself, below are a few methods for how to unclog a shower drain with standing water.

How to Unclog a Shower Drain with Standing Water?

Method 1: Pour the Drain Water All the Way Down

This way can break down the blockage of the drain. You can clean the grease or soap that hold the clog in a piece by pouring the boiling water at the blockage.

However, this method might not work if you are suffering from some serious issues with clogging. In this case, pouring the boiling water may clear up the blocks partially.

Method 2: Try With a Plunger

Another vastly used method for unclogging a shower drain is the using of a plunger. Well, how effective plunging will be, depends on the type of the drain blockage. The design of your shower drains and where exactly the clogs are, etc. Determine the success of plunging. For example, you may struggle a lot to get enough suction for an effective plunging, for a deep and matted hair clog.

To get a better seal you can use petroleum jelly at sucking pad edge. Also, add water to the shower and submerge the bottom line of the plunger. In my experience, plunging method has a low success rate usually. But, the cost, as well as the time involved in it, is minimal and so it’s always worth a try.

Method 3: Using Baking Soda and Vinegar

If you want to do it in a non-chemical way, you can look forward with baking soda and vinegar. This process is preferable ecologically and also do not damage the plastic pipes. At first, take a cup of baking soda and pour it down the shower drain. Now, wait for several minutes. After that, take another cup of poured vinegar too down the drain.

After waiting a couple of hours check if the hair clog is still undissolved or dissolved. When the clog dissolves, pour some hot water through the drain and clean out it.

Method 4: Remove Cover and Take the Clog Out

This way has a pretty decent success rate. However, this may ask for using your hands in some cases. So, make sure you have a pair of rubber gloves as you are starting.

At first, using a screwdriver unscrew the cover of the drain and take off it. Then, watch the inner view of the drain and find the position of the clog. If necessary, take a flashlight. If you see that the clog to be reached by hands, pull out it with the fingers. If you can reach the clog with your fingers, use a hook and unclog it.

Method 5: Use Chemical Cleaners

Most supermarkets sell many kinds of stubborn cleaners that are non-chemical that can unblock drains. Carefully go through the instructions and then use it. Don’t deal with the chemicals lightly. They can damage the drainage pipes, especially if you use them repeatedly.

To use chemical items is an easy, quick and affordable method. Minimize the usage of chemicals by avoiding future blockages of your shower drain.

Final Thoughts

When you find yourself standing in your shower in a deep puddle of water, it’s very irritating. Once the drainage problem starts, it usually gets worse over time. The sooner you deal with the problem, the easier you can resolve it. That’s why, instead of waiting for a plumber, you better start the unclogging process by yourself. Now, as you know the methods, you can simply unclog your shower drain with standing water. Collect the necessary tools and follow any method to unclog your shower drain.

How to Remove Bathtub Stopper?

As long as you are a serious homemaker, everything starting from the air conditioner to the bathtub stopper do matter for you. And if we talk about bathrooms only, one of the concerns of us all is, Is the bathtub stopper working properly?

If it doesn’t you don’t hesitate to buy a new one. But the problem comes in when you try to remove the old one. In fact, it’s not as easy as it sounds.

Bathtub stopper is one tiny part of the bathroom that influences the overall functionality of the bathtub. They are often termed as drain stopper as well. In this article, you’ll have a complete overview of replacing the bathtub stopper in easy steps-

How to Identify the Type of Stopper You Have?

There are several types of stopper available. If your bathtub doesn’t have any trip lever installed in, it can be a Push Pull, Toe Touch, Lift and Turn or a Flip It stopper. No lever mechanism is behind their functionality. And, that’s why they can remove or replace a stopper with ease. Read the following description to identify the type of stopper –

  1. Toe Touch: You can open or close this stopper just by pushing it up with toe.
  2. Push-Pull: It has a central knob in its structure. To open it you have to pull it up and push it down to close it.
  3. Flip-It: You can open or close it by flipping its toggle from side to side.
  4. Plunger Style Stopper: This particular type of stopper works with a turn style of trip lever mechanism. What it does is, when you press the lever or the plate, it makes the plunger to be higher or lower in position. That’s how it stops or starts the waterflow.
  5. Lift and Turn: To open or close it, you need to lift and turn the stopper in opposite directions. It is a little similar to the push-pull style stopper.

6 Pop Up: The last type of stopper is pretty similar to the plunger style stoppers. They also work with either a turn style or a trip lever. The operation is based on an internal plunger that controls the entire waterflow.

Removing a Bathtub Stopper

Toe Touch Stopper: If it’s a toe touch type, the stopper needs to be unscrewed by turning it in counterclockwise. When you push it down once, this stopper stays down. When you push it again, it opens up. If you can’t remove the screw by hand, wrap a towel around the screw. Then grip and turn it with an adjustable plier.

 Push-Pull Stopper: The stopper may be in the ‘open’ or ‘closed’ position. The first step is to get the knob off the top of the bathtub stopper. Hold the stopper and unscrew the knob. You need to use both of the hands to do this. A flathead screwdriver is essential to turn it counter-clockwise. Finally, lift the stopper from the strainer.

Flip-It Stopper: Open the toggle of your flip-it stopper. This style uses O-rings for sealing the drain when the toggle remains closed. Now, wiggle the stopper back and forth and thus loosen the O-rings. Lastly, lift the stopper out of the drain.

Pop-Up Stopper:  This style is operated by a mechanism on the overflow plate. Some faceplates have a trip lever which moves up and down. Again some have a lever which rotates either in left or right. Besides, many stoppers have entire faceplates rotate on cable operated bath wastes. To open it, flip the trip lever, otherwise rotate the overflow faceplate.

Lift and Turn Stopper: The removal of a lift and turn stopper is like the removing process of a push-pull stopper. When you push and twist a lift and turn stopper, it stays down. The parts of this stopper are also identical to those of a push-pull stopper.

Plunger Style Stopper: If your bathtub has such stopper, remove its lever cover plate. The real stopper is located behind the tub wall. Also, the drain has a strainer. When you’ve unscrewed the cover plate, lift it and handle it straight up. So, the plunger linkage will also come with it. Finally, unscrew the strainer by using a screwdriver in order to access the drain.

Final Thoughts

Removing a bathtub stopper is not so difficult once you know the tricks and have the necessary tools. Identify the type of your bathtub stopper and get engaged to remove or replace it when needed. So, why spending money employing a plumber when you can do it by yourself? Read the guidelines discussed in the article. Follow the steps and you will find it very easy removing your bathtub stopper.

How to Use a Boning Knife?

Are you trying to find the right knife for deboning the meat? Looking for a knife to make those thin cuts like the master chefs? Then look no further. Because a boning knife can fulfill all of these wishes.

A boning knife is a great tool when it comes to separating the bones from the meat. But you can utilize them for multiple purposes. In short, a boning knife can be a perfect helping hand with your daily kitchen chores.

What is a boning knife:

A Boning knife is mainly used for separating the bone from the meat and fish or removing the skin from the meat.  A boning knife features a sharp and narrow blade edge. It is normally from 12 cm to 17 cm in length.  With the help of this knife precision cut are easy to sometimes comes with a curved edge.

There are both stiff and flexible boning knives. A stiff boning knife offers security during the meat separating process. On the other hand, the flexible one is great for precision.

Uses of a boning knife:

A boning knife can be utilized in many ways.

Deboning the meat:

Boning knives are meant for removing the bones from the meat as the name suggests. As the blade is narrow, it can reach every side of the bone attaching to the meat. The knife makes it easy to separate the meat from the bone without damaging the meat or cutting the bone.

Separating the skin:

The narrow blade of a boning knife can be used to remove the meat skin. The blade cut through the connecting tissues between the meat and skin so precisely. Thus getting a fine and easy skin removal.

Removing the fat:

Sometimes the bone maybe hiding under a layer of fat. So to separate the bone first we have to get rid of the fat. A boning knife does an excellent job of getting rid of the stubborn fat on the meat. A flexible boning knife will get the job done as a dream.

Slicing the fish:

As the fish flesh is so delicate, a boning knife is perfect for cutting them into precise pieces. You can also use the knife to separate the flesh from the skeleton.

Meat Scouring:

A boning knife does an excellent job when it comes to scouring the meat and the fish.

Replace the cookie cutter:

If you can’t find your cookie cutter when required, just grab your boning knife. The shape and flexible edge of the knife will perfectly replace your cutter. You can use the knife for other baked food as well.

Slicing the mangoes:

As the mango has very soft and juicy interior, a precise boning knife will be perfect to slice it. This way less pressure will need and the fruit flesh won’t damage.

Detach the apple core:

As we all know how tricky splitting an apple core can be. It also wastes most of the fruit. Don’t worry, a boning knife is there to help you. Now you can separate the core without much effort.

Decorating the cakes:

A boning knife can assist you in decorating or trimming the cake for further decoration. You can make a nice cut of the cake as well. Making center holes for fillings can also be done with a boning knife.

Final thoughts:

Now you know how multipurpose a boning knife can be. So it will be a good option to invest in a high-quality boning knife. Go for a stainless blade.

Before buying a boning knife study about its size and angle as per your requirement. A good flexible boning knife will help you to make a precise cut like a pro. And the stiff one will make the bone separation easy as a dream.

Don’t forget to wash your boning knife properly after each use. This will make the knife long lasting.  This way you can enjoy the great performance of the boning knife for a long time.

How to Unclog a Bathtub Drain With Baking Soda?

At one morning you are seeing your bathtub drain has been clogged. Not only that, from there smell is coming out. Well, sometimes caustic cleaners can’t remove the clog or maybe the apartment management won’t allow the use of it. So stay on the safe side and choose baking soda for unclogging.

Baking soda may not be the first choice for cleaning the bathtub drain but you better know that it is the easier solution to apply. Again if there is some kind of limitation about using chemicals this is the best solution. Some cleaners aren’t actually can able to remove the clog, in that case, if you know how to unclog bathtub drain using baking soda then you will be the beneficiary. Do you want to know the procedure? Then you are in the right place. Here stay with me and have the whole procedure.

Unclogging bathtub drain using baking soda

There are few steps you need to follow when doing this. Those are given here:

1. Cleaning the strainer or stopper:

You are cleaning bathtub drain so it’s usual to have hair and other residues underneath the stopper. These may be over or under it. So first you need to remove these things and then open up the strainer losing screws. Then twist the stopper so that you can remove it. Any junk you can see take aside or scrub those.

2. Boiling water in a tea kettle:

There is no specification regarding water that how much you need to use when doing your job. So you may pour water on the top of the kettle. Wait until water starts boiling and let it boil properly. If you do not have a tea kettle or you want a bigger pot, then you can use a large pot of boiling water.

3. Pouring water into the drain:

The boil water may work at this point by unclogging the drain. Turn on the bathtub so that you can see if the draining process is normal. Stay away from splashing the hot water as it can burn you and it’s dangerous.

4. Pour baking soda with vinegar down the drain:

Take ¼ cup of baking soda in a cup and full another cup of vinegar. Pour these two cups of baking soda and vinegar into the drain. Baking soda along with vinegar helps to remove excessive gunk from the drain. And the hot water was for initial cleaning.

5. Wait 15-20 minutes:

Use a timer to keep the record when you have poured these two substances into the drain. Leave these in the drain for 15-20 minutes so that these can work properly.

6. Boil more water:

Again you need to boil water so follow the same procedure for boiling.

7. Pouring water into the drain:

The water you have burnt, pour this into the drain. This will react with baking soda and vinegar which helps to unclog the drain. Then test your bathtub and see if there is any clogging or not.

There is no use of chemical and almost every time this procedure works well.

Benefits of using baking soda

The question may come to your mind why will you use baking soda rather than anything. Here is the answer-

  • Harsh chemicals sometimes leave odor and residue in the bathtub. But when you are using baking soda there will be no odor left that you can’t bear.
  • The combination of baking soda and vinegar is environmentally friendly whereas some caustic chemicals develop contamination. Again children may get affected by these serious chemicals.
  • In your home, some family member may not tolerate the smell or odor of other chemicals. Baking soda won’t affect anything.
  • It costs not too much so you can easily afford it. This also works well on surfaces of your home. Therefore, you can use this also for other cleaning purposes.

Final verdict

Now you can see how easy is the unclogging of the bathtub drain which you yourself can do so easily and no need of sweeper! When you go for a trip you can put baking soda down the drain and don’t rinse. It will help to resist the odor that can produce when you are not at home. so undoubtedly you can choose baking soda for your bathtub drain without any second thought!

How to Select Quality Kitchen Knives?

If you have questions about how to choose the best knife for your kitchen, then welcome. Next is the question what do you mean by a knife? The knife that is fashionable, as well as durable, is a quality knife. And you also want to purchase it at a reasonable price, don’t you?

When you’ll go shopping, you’ll find different brands and styles for different purposes. But consider some facts before you pick one and bring it in your home. Below are some tips that’ll help you select the best one for you.

Tips for Kitchen Knives

  1. Know your purpose. Knives vary in size shape and different knives will serve you a variety of needs. So the first step is to decide. For what purpose you’re buying one. You’ve different options
  • Multi-purpose utility knife
  • Chef’s knife mainly for dicing, mincing, chopping, and cutting
  • Paring knife for vegetable peeling, cutting and trimming
  • Bread knife for slicing bread, cake, soft fruits.
  • Filleting knife for filleting fishes.
  • Carving for slicing small pieces from a roast.
  • Cleavers are mainly for chopping meat and sometimes also small herbs.

If you need various types at a time, then buy a set instead of buying each type separately. A set of knives that contains all of these varieties will be cheaper.

  1. Check, of which material the handles are made. Usually, it’s of toughed resins like strong materials. Or maybe of plastic or wood. Bone handles are old fashioned and are more likely to go brittle after some time. Even there are chances it crumbles your hand. So it’s wise to avoid them.
  2. Now check the blade, both the material and sharpness. Ceramic blades are mostly of scalpel quality and have a longer rust-free life. But this knife can be fragile and thereby can easily break.

Nowadays most of the cheap knives are usually of stainless steel. These are cheap. But these can go blunt after a few uses and so you may need to sharpen it often.

Rather look for non-stainless steel if you can afford an expensive one. Good materials are often in the form of carbon steel. They obtain sharp edge very quickly and you can do it at home. Buy care should be taken so that they won’t rust. Choose forged blades instead of stamped ones as forged blades are stronger.

If you have a fixed budget, you can go for stainless steel or ceramic those are relatively cheaper. But before finally bringing one home, you should view it with caution.

  1. Check the weight of the knife. Choose lightweight if you are going to use it for lightweight ingredients. It’ll give you both speed and precision. But applying for solid ingredients like nuts, palm sugar, choose a heavy one.
  2. Observe the width and thickness of the cutting edge. Smoothness and toughly polished without pitting is the sign of a good knife. From the tip of the blade to the hilt, equal sharpness should be present. Otherwise heavy cuttings like carrots will be difficult with this.

Caution- serrated chef’s knife can be dangerous if you are not an expert. They tend more to slip than cut. They are more likely for sawing rather than slicing. So avoid them for cutting vegetables and meat.

  1. Hold each one in your hand with which you work in the kitchen. Check, whether it’s comfortable when you gripped it and it sets in your hand rightly.
  2. Look for any sign of welding or joining. Check the hilt area of knife particularly. Having steel joints is a sign of those are weak and tend to bend or break easily. Therefore, it’s wise to avoid them.

Final Verdict

You should focus more on the quality rather than on the brand. At the same time, you must remember, how long your knife is going to last depends on how you’re going to use this. So don’t treat it badly! No matter How good quality your knife may have, if you leave it dirty and wet, it won’t serve you long, for sure.

How to Remove Shower Drain?

How tiring it is to keep standing in the soapy water every time you bath! Water drains out slowly when the shower drain is clogged by any means. In most cases, hair is the main culprit. Besides, soap or minerals of hard water may clog up the drain.

Whatever may be the reason, you should unclog the drain as soon as possible. Of course, standing in the dirty water while you are bathing isn’t something very comfortable. Now to clear the clogs, first, you must know how to remove the drain cover. So let’s learn how to do that.

Tools required

Some small tools will surely come in handy to save both your time and frustration.

  • Screwdriver
  • Caulk gun
  • Hacksaw blade
  • Pliers
  • Flathead
  • Lubricants

How to Remove shower drain?

The process may slightly differ regarding the drain type.

Most of the standard drain covers are screwed with one or two screws with a lower support. The most common type of shower drain has a Snap-On cover. All you need to do is to simply snap it on to the drain. It holds into place either by the silicone adhesive or by screws. To remove strainers those are held by adhesives, you must exert some force and then pull it.

Below is the step by step description.

How to remove adhesive

Step 1

First, spray some lubricants over the lip of the cover. Now, wait for a while so that the lubricants can settle into the threads enough.

Step 2

Then take a pair of pliers that have needle-nose like parts. Now Place the pointed ends at any two opposite sides of the drain. Then Insert the ends of the pliers into any two openings of the strainer.

Step 3

Finally, grip the pliers firmly and twist it to the left. Spay some more lubricants if necessary. Any drain cover placed by industrial adhesives will come off slowly.

How to remove screw-in type strainer

Step 1

Let the clogged water drain out completely first. Then wait for a few minutes more. Let the pipes be also free of water.

Step 2

If the drain has a convex or concave or flat strainer, then simply unscrew it. A 4 inch 1 screwdriver will be enough for this task. Also, don’t forget to keep a paper towel near at hand when you are removing the cover. Hair, as well as soap accumulations, may come out with it.

How to remove Push/Pull type covers

Step 1

First, turn the screw counterclockwise to remove the top knob of the stopper body. Use pliers. But hold the stopper body in its place. Use a rubber grippy or rag so that it doesn’t cause any scratching.

Step 2

There’s a brass insert underlying the knob. Also, unscrew it with the flathead.

Step 3

Finally, lift the stopper.

How to remove Lift-and-Turn type covers

Step 1

Lift it from the open position first. Now Look whether there’s any screw or not.

Step 2

If you see no screw, then simply turn the cover counterclockwise and remove.

Step 3

Or there may be a small screw. Use an Allen wrench or flathead to loosen it enough so that you can remove the stopper.

How to remove Toe-Touch type cover

To open and close the clover you better use your toe to push. That’s from where the name’s derived.

Step 1

Remove the cap First.

Step 2

Then turn the stopper counter-clockwise from the open position.

Step 3

In some models, there may be a shaft cylinder which turns with the cap rotation. Look closely to find the crossbar from where it’s been threaded. Now unscrew it.

Step 4

If you find any threaded slot in the shaft cylinder, remove it also with a flathead.

How to remove Pop-Up Covers

Some of the pop-up covers can wiggle back and forth. Others, you can pull up and off straight. If the cover is of rocker-arm style, then you have to pull it up. You’ll see the arm as you pull it up.

How to remove Flip-It Style Drain

If your shower drain contains this type of stopper, you won’t need any tools to remove it. Simply grasp the body of the stopper and not the toggle and pull it from the drain. Don’t forget to rotate while you are pulling it up.

Final Verdict

I hope you don’t have to fight with your bathtub drain and tolerate the annoying clog-up problem anymore. Identify which type of drain cover you have and collect the necessary tools for this project. It doesn’t sound something difficult, right?

How to Maintain Your Kitchen Knife?

Buying the best quality knives is not the end of the task. What comes next is how to maintain a knife. Surely, you want the knife you’ve purchased with your hard earned money with much precision would go long. Don’t you?

Maintaining deals with the way you are using, cleaning and storing it after use. No matter how sharp and strong the blade is, it’s still a piece of metal. So it can go rust, bent and thereby damaged if you constantly mistreat it. Besides working with a dull knife can be dangerous.

Check the do’s and don’ts regarding maintain your knife while it’s in use.

Maintenance while using

  1. Always cut ingredients on a cutting board.

Never cut on a too-solid surface like countertop made of granite, marble or glass. These will make the blade dull very quickly which will be unyielding for your knife life. Now coming to the cutting board material, there are wooden and plastic cutting boards. Choose wooden instead of plastic.

  1. Often sharpen your knives.

Unlike our everyday life, your knife also needs to be tuned up. Sharpening and honing do this tuning up. Honing recalibrates the angle of the blade and removes the nicks. You can sharpen your knife annually but you should hone it more often. Use a honing steel, electric sharpener, knife stone or take it to someone professional.

  1. Frequently clean it while cutting with it.

Rinse the knife off and then wipe it to prevent building up germs on the blade. It’ll also prevent the knife from dulling and maintain the efficiency.

Maintenance while washing

  1. Wash your knives with your hand instead of in the dishwasher

The moisture, heat and the detergent are deleterious for the knife. They will discolor and dull your knife. Again, your knife may be rattling around with other utensils thus will get dinged. Use mild soap and hot water just after you are done using it to prevent scratching, corrosion or bending.

  1. Avoid leaving the knife floating in the sink for long.

It can be dangerous for whoever will wash the dishes. Also, your knife will tend to scratch, the tip may bend or break. You can let it float in mild soap and hot water temporarily. But remember to collect it after a few minutes.

After washing your knife, wipe it out with a dry towel. Don’t wait till air dry as this can lead to rusting and molding. Again, drying it on the drying rack with other dishes can make the blade dull.

Maintenance while storing

  1. Avoid storing your knife where it’ll ix with other utensils.

If you store it freely in a drawer, there are chances that it’ll break, chip and dull. Using blade cover will only minimize it.

  1. Store knife in a knife block or on a magnetic strip.

Knife block, nowadays, has become the most common storage medium. You can get all your knives in a place. Again a magnetic strip will store knives vertically on the wall you mounted it. This makes knives easily accessible. But if your knives are of ceramics, magnetic strip isn’t going to work well.

Some more tips

  • Sharpen the blades always in the same direction.
  • When you transfer food from the cutting board to the bowl, do it with the dull side of the knife.
  • Use a utility knife or must use different knife regarding cutting different items. Using small knives for heavy items is life shortening as well as equally dangerous for you.
  • While washing, be careful that the blade and the tip are away from your body.

Final Verdict

Use it, wash it, dry it and finally store it correctly, that’s the motto of a longer lasting knife. Of course, you cannot use one knife throughout your life. But you can certainly extend its lifetime. Just think, how much your knife does for you every day. And all you have to do is to use it correctly.

How to Dispose of Knives Safely?

Your knives aren’t going to last forever. So when you’ll go for a brand new knife, what should you do with the old one? Getting rid of your old used knives relates to your safety. If you don’t dispose of it properly it may be the cause of someone’s injury.

There are some methods of disposing of your knives. Choose whichever seems most convenient for you.

Step 1: Wrap the knives

There are different options regarding which material you want to wrap it.

Bubble wrap

This is probably the best option as it ensures the safety best during disposal. Before wrapping with the layers of bubble wrap, you can wrap it with butcher paper first. To keep both the layers secure, wrap them around with duct tape.


Obviously, it’s a sturdy material though you may not always find it near at hand. Be a bit innovative when you are wrapping with it. Place it on a cardboard which is longer and almost double of the size of the knife. Place it such that only the blade portion lies on the cardboard. Now fold the cardboard over to encase the blade inside the cardboard. Finally, seal the two edges with sufficient sticky tape.

You can use an old shoe box before throwing the knife away. This method is effective especially when you decide to donate it.

Other materials

Newspaper, wood, hard plastic, thick cloths or socks will also work well. If you want to wrap it with cloth or newspaper, take at least 5 to 6 sheets or pieces of cloths to ensure thick padding. Wrap the blade carefully so that no area especially the tip of the blade is left exposed. Leave the handle unwrapped so that anyone can handle it easily.

Don’t hesitate to use sufficient tape so that the cloth or the newspaper remains in place.

Step 2: Now dispose of it.

Once again there are several options. Choose one that you consider would be the best.

Method 1: Donate it. It’s the most worthy way to dispose of your knives. Your knife may not satisfy you anymore but it can certainly do the work for someone else. A dull blade can be sharpened and thereby reused. Check whether there’s any company that collects the old utensils and makes it reusable.

Method 2: Recycle the old knife. Recycle them only when you are sure that your knife has come to its end and is not in a condition of donating it. In spite of the blade became dull and bent but the handle may be still in a good condition. So it can make great recycled materials. Check whether there’s any recycling center in your locality that accepts metal. If you are not sure about the center’s policy, contact them during working hour. Again, don’t forget to secure it before handing it over.

Method 3: Make a contact with the knife sharpener who is professional. No! It’s not for sharpening the old knife and reuse them. Obviously, you’re sure that your knife is no longer up to the standard. But it can be useful for a knife sharpener as he may use it in repairs.

Method 4: Sell it. Differed metal stores buy old scrap metals. But first, be sure about of what materials your knife is made. Most of the knives are usually of steel, iron or sometimes the mixture of the two. Depending on the metal, you will get the price.

Method 5: If you can neither recycle nor reuse the knife, then throw it away in your garbage. But don’t just throw it away. As I said above, ensure that your knife won’t cause any injury to anyone. Therefore, wrap it properly or seal it in a box before tossing the knife/knives in the garbage.

Final Verdict

The knife you’ve used so dearly, don’t just throw them like junk staff. Just because they can no longer serve your purpose doesn’t mean aren’t functional anymore. Think the safety of yours as well as someone else who will get it.

How to Install a New Kitchen Faucet?

Do you believe yourself to be a DIY guy? Then, you definitely don’t want to pay off some extra bucks to install a new faucet on your kitchen. And in case you’re preparing to install the faucet yourself, this is the guide you must read.

Installing a faucet doesn’t begin with the setup process actually. To be straight forward, you have to be careful since when you’re purchasing a kitchen faucet.

Here are a few stuffs to check before you buy and install a faucet-

  1. Look through the bottom of the sink and check how many holes does the sink has. In general sense, there can be anything can be one to four holes.
  2. If you have 4 holes on the bottom of the sink, make sure you get a deck plate with the faucet you buy.
  3. Make sure you have the right set of accessories(gasket, nuts) with the faucet model.

8 Steps to Setup a New Kitchen Faucet

Now, we’re at the core of the articles, for what you’ve actually landed on this page. Here are our 8-steps formula to replace your own faucet of the kitchen and replace a new one instead.

Let’s start-

Step 1: Loosen up the Old One

If you’re not using a faucet for the first time (which is pretty rare case), you have to put off the older faucet in the kitchen. If you’re actually new to such faucets, or installing one for the new home, then skip this step.

Turn off everything that connects to the waterline of the faucet. The list includes the sink tapes, the water valves, the disposal power and anything else, if applicable. Finally turn on the tape of the older faucet to release the pressure inside.

Take a picture of the plumbing setup, in case you need it for later.

Step 2: Remove the Old Faucet

As you’ve disconnected every sort of connections to the older faucet, now it’s time to move that off. You may need a helping hand who would hold the faucet in place while you’ll be loosening up the bolts and nuts.

Step 3: Clean the Sink Off

Before your setup a new kitchen faucet, it’s good to do some cleaning works on the sink’s surface and waterline. Most commonly, sealant and grime are the stuff that sticks the sink around. There are a few chemicals available to deal with such stubborn. Or you can also use a scrubber.

Step 4: Go Through the New Faucet’s Manual

As you know, every faucet has something new in it that differs it from others. In case you used something exactly similar, it’s better to guide yourself through the product annual.

Step 5: Set the Deck Place

As I’ve mentioned before, there can be a gasket in need if you chose to setup a 3 or 4-hole kitchen faucet. To set it up, use a plastic or rubber gasket, and a trim ring over the surface of the sink. And setup the gasket on it.

Later on, feed the faucet lines into the holes you have in the sink. The excess of pipe should be under the sink through the holes.

In the step of placing he gasket, there can be misalignments in dimension. So, it’s wise to use temporary chalks to be sure about the central placement of it. There is also a stuff called Plumber’s Putty that may be help you out.

Step 6: Install the Nuts and Washers

Now move yourself for some job underneath the sink. As you’ve places the pipes in the waterline, you need to setup the nuts and washers. For faucets that are pull down or something similar, use a quick-connection hose before you tighten up the nuts.

Step 7: Connect the Water Lines with the System

Now it’s one of the most crucial steps of connection your house’s water lines to the faucet. If you’re sure that you’ve bought the right faucet for the kitchen, then take advance thanks. The rest of the process will be too easy for you.

Connect the water supply lines to the pipes of the faucet. To joint them up, a plumber tape can be the best solution.

Beware of overtightening the connections. They may end up in mishaps.

Step 8: Remove the Aerator and Check for Flaws

We’re almost done. Now it’s time to proofread your work. Check for any leaks on the entire system with slow flows of water. Don’t forget to take away the aerator from the faucet head.

Run a decent amount of water till you’re sure about no leaks or flaws on the entire system.

Bottom Line

If you’ve gone successfully, then congratulations! You’ve just did your own plumbing of setting up a new faucet. Once you get done with it and know it’s pros and cons, every time you setup a new one, would look like no trouble at all.

Keep up the good works. Cheers!

How to Install a Bathroom Faucet?

So, you have just bought a shiny new faucet for the bathroom. Now what?

Well, you can call up a plumber and cost yourself a few hundred dollars more. Or, if you want to be on safe side with cost, you can do it yourself. Homemakers around the country are being smarter about doing their own stuff. So, why don’t you?

In case you’re new to setting up a bathroom faucet, this is the article you should read must. Because in here, we’ve illustrated the easiest possible way to install a bathroom faucet manually. So, hold tight and go through the entire guide-

What You Need to Know Before Installing a Bathroom Faucet

Before you start the task off, make sure you know what you’re about to do.

A bathroom faucet usually consists of a few parts of them. Although it varies from brands to brands, the basic parts are all the same-

  1. Faucet Aerator.
  2. Faucet Cross Arm.
  3. Faucet handle.
  4. Faucet Aerator kit.
  5. Faucet lever handle.
  6. The fisher.

So, the very first task is to identify what parts your faucet has got and understood the basic function of each and one of them. You can take help from the manual or simply google about the model.

If you’re done with that, it’s time to move to the action.

Steps of Installing a Bathroom Faucet

  1. Step 1: Remove the Old Faucet (If You Have One)

    It’s not like that every one of us who buy faucets is using it for the first time. In case you have an older one and want to replace it with the faucet you’ve just bought, you should remove the old one first.In case of an existing faucet, it will be either a single hole faucet or a 4 inches triple hole or an 8 inches triple whole faucet. If your old faucet is found to be anyone these three, then it’s maybe on the countertop of the bathroom. So, you have a complete liberty to change the faucet type if you can.Make sure that, while you’re replacing the old one, no parts or surfaces of the countertop base is damaged.

  2. Step 2: Assemble the Parts

    Now, take out the parts and the faucet itself from the box. Check the manual to understand the functions of each part. Based on your waterline extension, you may have to give a few trips to the local storehouse.As you’re getting a chance to fix up any errors in the water line, check for any leakage or malfunction on it. You can use auto leak shut off in that case.
    Also, some faucets may have inequalities with the water flow to your waterline. You can use a small valve on the base of the water line to adjust this inequality.

  3. Start Installing the Upper Half

    Now it’s time to consult the user’s manual once again and check whether you need any modification to that or not. Try to get a visual view of the entire setup.Usually, it will be the spout, a gasket, the sink, the plumber’s putty, large saddle etc. The plumber’s putty can be a new tool for home users like you and me. It’s nothing more than a grey modeling clay. All you need to do is to take a little bit of that on the palm and roll back and forth until you can form a half inches diameter rope shape. What is this used in? Well, if you have a chance to splash the water from the spout base, this rope is likely to prevent that.

  4. Setup and Place the Mixing Valves

    The basic difference between a single hole and a three-hole faucet is about the water mix. If you use a three-hole faucet, you will have two mixing valves which you have to set up at this stage.It consists of a washer and a nut. The nut holds up the valve and the washer tighten it up. You can apply the plumber’s putty to make sure there is no leak in between the washer and a valve.
    Just to give you a hint, the valve that brings hot water on the left side. And the valve that brings on the cold water is on the right side.

  5. Thread the Trim on the Mixing Valve

    The second last step is to thread the mixing valve. While you’ll be mounting this one, make sure that the handle is stood parallel to the wall. Usually, most of the faucets these days comes with an easy-to-snap and fit feature. So, this step wouldn’t be so tough, even f you’re new to this.

  6. Setup the Drain Rod and You’re Done

    Now, this is the last step. What you have to do is to reinstall the drain rod and tighten the bolt that’s with the clamp. Now check every single joint and junction of the entire system and use plumber’s putty while necessary.

How to Install a Bathroom Sink?

Installing a bathroom for home or replacing your old modelled one can be a comparatively easier job than what we think it is. If you have some basic skills and tools, installing it is a simple do-it-yourself job. Although, different kinds of sink need different kinds of installations.

If you know the nook and corners of this process, you can easily learn how to assemble and fit your new bathroom sink into the right place in a quick and efficient way. This article will assist you to understand the illustrated step-by-step procedures you need.

How to Install a Bathroom Sink?

Step 1:

Before starting the job, collect the required tools at first. Before setting up a sink in your bathroom you will need a number of handy kits and tools. Make sure to gather these tools, like –

  1. Silicone caulking
  2. Basin wrench
  3. Plumber’s wrenches
  4. Plumbing sockets

Step 2:

You need to turn the supply valves off, as no waterflow is expected during the setup process. These valves are usually located behind/under the sink. To check, turn on the hot and cold water supply lines. Thus, be sure that no water is coming out from the water lines.

Step 3:

If you are going to replace the bathroom sink, surely, you’ll have to replace the old one before installing the new one.

For this, disconnect the water supply first. While doing this, make sure you don’t damage any part of the countertop or wall. This is very normal. Use a towel or a bucket to collect the water which leaks out.

Step 4:

Check the dimensions of the new sink that’s about to be installed. Every sink has a template for mounting the opening. This template indicates the location of faucet holes. Use the template to be sure that the no mismatching is taken place. If the sink doesn’t fit, you may have to trim the opening to match the dimension.

Step 5:

At this stage, put the new bathroom sink in the installation space and mark the board with a caulk. You can use a layer of silicone at the lower surface of the sink and put it into the hole. Then, clean up the excess silicone. To install under-mount sinks, keep someone to assist you and put silicone beads under it. Also, install the connecting clips that are included with the sink. Again, if you’re going to install it in a granite or stone counter, make some holes at the beginning by using a diamond carbide tip.

Step 6:

Now, secure the new sink using the clips. The clips act as a lever and thus keep the entire sink stable at its position. Read the instructions in the manufacturer’s guideline and proceed the works accordingly.

Step 7:

Now it’s time to install the faucet set. First, anchor it by reaching up to the underneath of the sink. A nut locks set comes with the box and you can use that on the purpose.

In some cases, installing the faucet first, and installing the sink later can be easier. It depends entirely on the counter design and fixtures of the sink. Again, make sure that the faucet space matches with the sink location.

Step 8:

Now, we are about to setup the tail pieces of the set and also the drain kit. You can use the screws to set the tailpiece at the bottom surface of the sink. Many sinks have gaskets that go between the tailpiece and the sink. In that case, the gasket and the cardboard washer are included with it and also the locknut. And thus, make sure the tailpiece is well placed.

Step 9:

We’re almost done. Reconnect the waterlines that we disconnected at step 1. You should screw the water supply lines and strengthen the related joints on the faucet with a plumber’s tape. The connector’s size should be in the instruction manual.

Step 10:

Finally, check for the leaks by turning on the water. You can’t know if something is going to leak till you turn on the water. If there are small leaks, try tightening the connections more. The drain itself may sometime leak due to over-tightening the connector gaskets. If this is the case, don’t hand tight it. Instead, try a new washer to handle the drain leaking.

Final Thoughts

Installing a bathroom sink or replacing it is not so hard. You can do it simply by following some simple and basic rules. So, instead of spending money by hiring a plumber, you can save a lot. Read the steps mentioned above carefully and do accordingly.

How to sharpen a kitchen knife?

Pissed of with sharpening your kitchen knife every week?

I guess you are. Because, firstly you’ve clicked on this article and my second thought is, you already know that the way you sharpen the knife isn’t proper.

However, you’re not alone suffering from this. And trust me, sharping your knife is pretty easy.

It is very important to sharpen kitchen knives so that they cut through food with less slippage. A dull knife is dangerous because it requires more force cut something and so has a higher chance of slipping and missing the mark. Additionally, poorly cut food will not be cooked properly. A sharp knife will produce food that is properly cut and therefore you will have well cooked food. Whatever, let me tell you how to sharpen a kitchen knife.

Some Key Take Takeaways

While you’re thinking of sharpening your knife on regular basis, keep these few takeaways in mind-

  1. No matter how pricey or how good metal the knife is, it will dull over time. So, you have to do regular sharpening on regular basis.
  2. As a sharp knife can cut through foods and meats without any slippage, they are safe than dull ones.
  3. A sharp knife can help of to get thinner and finer slices of foods, veggies or meats. So, the can get the taste better as well.
  • Paper Test

You can check the sharpness of kitchen knives in a simple way. Take a piece of thin paper then take the knife. After that, try to cut the paper on one single slice of the paper. Did the knife slice smoothly? May be not. But if it were sharp, it should have.

Be careful from cutting off your finger tip while you’re testing the sharpness of kitchen knife.

  • Hon your kitchen Knife

Sharpening is often as possible mistook for honing, however it accomplishes something altogether unique. Honing includes expel material from the sharp edge itself, though sharpening basically rectifies the bleeding edge of a blade. This is important on the grounds that the forefront of a blade tends to overlap over on itself with utilize, which influences it to dull. Be that as it may, with sharpening, you can keep a generally sharp blade functioning admirably for quite a while before it’s important to pound away material and reset the edge’s edge.

  • Working with a Whetstone

Whetstones are less expensive than most other blade honing alternatives—and they’re more flexible—however, you need to focus on taking in the strategy. Whatever edge you hold the blade at while honing will turn into the edge of your edge, so on the off chance that you treat it terribly, you’ll wind up with a not as much as perfect cutting actualize. The acuter the edge, the more honed the sharp edge. You would prefer not to be coldhearted about blade honing systems.

  • Sharp your knives with steel

A steel bar can be a simple but effective way to shine and sharpen knives. But how do you start?
Go snatch a long steel made bar that accompanied your blade set. It’s known as a honing steel.

Make sure you’re right with your slicing angle and the edges of the knives. If you do it in wrong way, this can make the knife even less inefficient.

  •  Use an Electric Sharpener

Using an electric sharpener is another good option to do the job quite easily.

They come with an electric setup with a metal blade and a slot to put the knives on it. If you’ve got one for sharpening kitchen knives, place the blade on the slot provided. Now, you need to slide the knife throughout the slot and keep repeating the process.

Make sure you’re passing the blade to each side of the knife twice each turn. Until this step, you’re using coarsest stone. Not move to the finer stone to finish up the sharpening process. Pass the finer stone twice for each side.

If you’re done with sharpening the knife equally on both sides, rinse the knife and dry it up.

Bottom Line

Thanks for being till the very end of the article. We’ve explained a few common ways to sharpen almost every sort of kitchen knives around. But one common advice you would request you to memorize, and its about the safety. Make sure every time you do sharpen your knife, you’re safe enough with the process. When you’re going through a newer process, it’s better to get some expert hand beside you.

How to Use Kitchen Knives Safely?

Ever wonder how you can avoid the accidents you cause while using the kitchen knives?

Knives are our constant companion in the kitchen. But using them unmindfully can lead to dangerous situations.

These types of situations can be avoided by simply following some basic tips in our daily life. So why not know them and make our experiences with knives even safer.

Tips to use kitchen knives safely:

A sharp knife is a key:

The sharper the knife the safest it is. A dull knife will require more force to chop hence has more chances to slip off the hand. So sharpen your knives on a regular basis. Use any shaping machine or sharping steel to sharp than at home. You can also seek professional help.

Know the proper knives for the job:

Different knives have different designs for handling various type of job accurately. Go for the knife that is meant for your job.

  1. Use a chef’s knife for chopping the vegetables and fruits. You can cut them in dice or mince them.
  2. Use a serrated knife for bread or fruits with the harder exterior with soft interior.
  3. Use a peeling knife to peel off the fruits and vegetables.
  4. Use utility knife for daily light chores.

Select a knife with the right size and weight as per your preference.

Don’t use your knife for any purpose rather than cutting. Using it for opening a can or instead a screwdriver is dangerous.

Choose the right chopping board:

Cut on a plane surface. Go for a wooden or plastic board that will seat properly and won’t slip.

Never use your palm as a cutting surface.

Know the proper chopping rules:

  • Holding the knife properly comes first in the chopping rules. Use pinch grip method for this. Use your thumb to place the knife in your hand from one side. Our index will be on the upper side of the blade. Remaining three fingers will be on the handle. This will give a firm gripping as well as precise control. Always use hold the knife in your dominant
  • Always keep the tip of your blade on the board. This will act as a guide point for you to properly lift the blade.
  • Always cut away from your hand. Curl your hand and keep your fingertips inwards. Guide the vegetables or fruits with your fingertips. Your knuckles should be in contact with the flat side of the blade.

Clean the knives properly:

Never leave your knives in the sink to wash later.  They can be dull for being soaked in water for long. Also, you can cause an accident by unknowingly poking the knife in the sink.

Clean them right away with dishwasher and warm water.

Store immediately:

After washing the knives, rub them with a towel and put them in the store immediately. Some knives also come with a head like attachments .use them to cover the sharp blade. Use a rack or knife organizer to store them properly.

Careful while carrying:

Don’t mix your knife with other things while carrying them. Use protective heads to prevent any accident. Never carry a bare knife in your pocket.

Avoid licking the knife:

If you try to lick the food direct from the knife, you are just asking for unwanted troubles. Don’t lick the jam or cheese from the cheese knife.

Proper holding:

Hold a knife facing the blade down while walking.

Never try to catch a falling knife. Never try to pass a knife by throwing it.

Keep it out of children reach:

Keep the knives in a place where the children can’t reach them easily. Even if they need to use the knives, don’t leave them alone.

Final thoughts:

As knives are our daily companion in our kitchen, we better pay attention to them. Don’t rush. Take your time with the knives. Try to grasp all the technics for maintaining the knives properly.

Take a good care of the knives. Sharp them frequently. This way you can make the daily kitchen chores mare enjoyable and safe.

How to Make a Living Room Cozy?

A living room is a place where you want to hide you after passing a long tiring day. So why not make it cozy and comfy! Especially when you are living in the cold climate, you probably prefer to stay indoors. Why just wait for winter to pass. Let’s make it peaceful and enjoyable.

Making your living room cozy is not always refers to luxurious and expensive staff. But it’s about surrounding yourself with the favorite color and the things those make you jolly.

Below are some ideas on how you are going to make your living room cozy.

Traditional way

Choose furniture with curved lines and also soft fabrics. Traditional architectural design creates a sense that put you at ease.

Intimately cozy

Provide a small intimate seating arrangement in front of the fireplace. It creates a wonderfully warm atmosphere. Also, choosing soft fabrics, ample window and warm colors will simply add to this comfort.

Using wood panel

Many people believe, using wooden panel will give your room 70s look. But you can also give a sophisticated look by using this same wooden panel. The warmth of natural grain creates a different character and depth which you won’t find in the paint.


It’s another important fact to consider. Use lights from various sources like ambient, accent, and task. Place the lights at different heights. It would be the best to use bulbs with a soft glow and without a bluish tint.

Gray walls

The color of paint on your wall largely decides the coziness of your room. Dark colors are warm. When you are enveloped in a dark room, it gives you the feeling of being in the midst of a hug. The dark color is also a symbol of intensity. But take care so that there’s sufficient access to light so that the room doesn’t look like a cave.

Cozy fireplace

In winter, nothing can make your room as cozy as a fireplace does. You can easily understand the significance of a fireplace. There is traditional wood burning fireplace you can choose if you have the supply of woods. Again, gas fireplace or an electric fireplace is just as well to create a cozy focal point.

Playful look

When we are talking about making a living room cozy, fun will definitely be a part of it. Decorate your living room with playful fabrics. And decorate the walls with books having colorful covers.

Bohemian style

This relates to casual vibe. Decorate the room with rumpled fabrics and tactile fabrics. Soft oodles of pillow will welcome you to sin on it and relax. Moreover, the item that every cozy room requires is a cable knit throw. This is the coolest that gives you instant warmth!

Robust room

This refers to a room full of furniture and other accessories. Using a lot of colors and patterns will further add to the coziness. But as I mentioned above cozy living room is more than how it looks. But its more about how you feel. Therefore, make sure that the furniture are comfortable and the fabrics are soft to touch.

Elegant look

Elegance largely depends on how you arrange the furniture. Therefore, it’s wise to arrange them around a central point. Also, create conversation areas. Provide some space between the wall and the furniture. It’ll create an intimate arrangement. Choose furniture those aren’t too severe. While buying fabrics, Remember, softness is the main feature to consider.

Colorful look

Colors have the power to cheer you up instantly. So colors can be an important fact to consider in making the living room cozy. Decorate the sofa set with lots of fluffy pillows.

Using pops of color will make the room exuberant. Bring variation in choosing colors of different staff.

Final Verdict

At the end of the day, you will like to see the room that comforts you from the inside. Of course, your taste and preference will get the priority. But considering expert’s advice will be wise.

How to Install a Pedestal Sink?

Thinking about redesigning your old vanity? Wants to add a cost-efficient yet stylish sink to your compact bathroom? Then the pedestal sink is the best answer for you.

If you are having trouble with a small bathroom space, then try to install a pedestal sink instead of the vanity. These are very space efficient and elegant as well. This type of sink will add a new look to your bathroom in your budget.

What is a pedestal sink:

A pedestal sink is consists of two parts, a pedestal which acts like the stand and the sink. The pedestal also houses the plumbing .the sink is balanced on the pedestal and mounted on the wall by brackets.

But before going for a pedestal sink, you have to consider whether it is enough for your need. You have to give up the luxury of the vanity, as it comes with the cabinet. Though adding a wall shelf may help a lot in this case.

Tools required:

  • Pedestal;
  • Sink;
  • PVC pipes;
  • Plumber’s putty;
  • Saw;
  • Wrench;
  • Drill bits;
  • Screws;
  • Drywall;
  • P -trap.

Steps to Install a Pedestal Sink:

Find the perfect match:

Finding the perfect set can be pretty tricky sometimes. There are different types of design for different purposes. So keep that in mind.

Calculate and measure the height of the sink and buy a pedestal likewise. Take note of the current position of the plumbing and match the design accordingly.

Decide whether the plumbing will be totally hidden or visible. Also, consider your floor and wall condition.

Also, don’t forget about the brackets. Find the perfect bracket set as for your requirement.

Remove the previous vanity:

Turn off the water line first. Then cut the lines.  Remove the top carefully. Loose the screws of the vanity base. Remove the base. Take out all the previous hangout screws from the wall.  Put these parts aside.

Make sure to check all the plumbing is okay to use again. You can replace the plumbing at this stage if needed.

Drill, drill, drill:

Drill the wall for mounting the support and brackets for the new sink. Measure the height of the drilling properly.  Insert the support and brackets there. You may need to drill your floor as well.

After properly adding the support, add some drywall to secure the holes.

Put the hardware:

Before installing the sink, attach all the hardware such as the taps, valves and handle to their proper place. Connect the supply lines to the taps at the downside of the sink. Screw them properly.

Never over tighten the screws.

Connect the drain:

Apply enough plumber’s putty to the flange and attach it to the sink. Attach the drain to the flange. Connect the water supply line the main source.

Connect the p-trap.

Draw the outline:

Draw the required space outline for your base on the floor and on the wall for the sink. Find the center line of the sink and pedestal to install it properly. Match the hole of the setup to your supports.

Set the pedestal:

According to the previously drawn outline, mount the base on the floor. Attach it to the supports. You may need additional support regarding your design.

Assemble all:

Assemble the base and the sink. Mount the sink with the help of the brackets and bearing on the wall. Adjust the weight of the sink by balancing it with the base.

Hide the plumbing:

Though visible plumbing also looks good, many bases have space to hide the plumbing. So if you decide to hide the plumbing insert it within the pedestal.

Floor and wall:

After getting done with the installation of the sink itself, take note of the floor and the wall. You may need some additional painting on the wall or add new tiles to the floor.

Final thoughts:

A pedestal sink can add a luxury to your bathroom without costing you so much money. Do a proper research about the designs of the sink. So you can get the best that will go well with your bathroom space.

Follow the steps mentioned above. This way you can install a pedestal sink like a professional all by yourself.

How to Install a Kitchen Sink?

Are you going to change your existing kitchen sink? Then you can hire a plumber or do it yourself. But installing a sink isn’t as easy as fixing the faucet only. In fact, it’s a bit more challenging. You’ll also need some complicated tools to do that.

The installation process also varies depending on which type of sink you want to install. There are single and double bowl drop sinks.

As most of the house kitchens have drop-in sinks, we’ll discuss it only.


  • New sink
  • Putty Knife
  • Plumber’s Putty
  • Putty Knife
  • Pipe Wrench
  • Hacksaw
  • Pliers
  • Socket Wrench
  • Shop Towels

Part 1: Removing the old one

Step 1

First, turn off the shutoff valves below the sink.

Step 2

Now turn on the handles of the faucet to relieve the existing pipe water.

Step 3

If your sink has a garbage disposer, then unplug it. But before doing so, don’t forget to turn off the circuit. You’ll require pliers to disconnect the P-trap and drain pipe.

Step 4

Next, check the manufacturer’s instruction to know how to remove the disposer. Work according to that.

Step 5

Now, below the counter, there are metal clips. Locate them around the perimeter of the sink. Then loosen the clips with a socket wrench and then swing them.

Step 6

Now draw a utility knife around the sink to cut the caulk. Then push the sink from below to lift it away.

Step 7

Now you have to remove the caulk, grime, and any old plumber’s putty. Use a putty knife to remove them from the countertop.

Part 2: How to install a drop-in sink

Step 1

First, Verify whether the new sink fits in the countertop hole or not. If not, then you have to modify the opening. Place the sink in the opening and turn it upside down. Then Trace the outline and cut it out with a jigsaw.

Step 2

Now Remove the sink and attach the clips inward toward the bowl.

Step 3

Now install the strainer. Apply some plumber’s putty around the drain strainer and press it firmly. Use a soft towel to remove any excess putty.

Step 4

Now place the rubber gaskets. Tilt the sink and secure the gaskets as well as threaded flange underside the sink drain.

Step 5

In case your sink has a garbage disposer, also install the mounting bracket to its bottom. Use a screwdriver. And also follow manufacturer’s instruction.

Step 6

Next, Apply silicone sealant at the edge of the basin. Now align the basin squarely. Then, below the sink, rotate the metal clips outward. Also, tighten the screws.

Step 7

Now attach all the water connections both of the supply pipes and the faucets. Install the garbage disposer, dishwasher drain. Also, connect the sink drain pipe to discharge pipe.

Adjustment of pipes

In case your new sink doesn’t line up to the old drainpipes, you’ll need some adjustment.

If the pipes are too long, you have to cut the pipes. Use a hacksaw to do that. Place a washer and slide a slip over it onto the pipe. Then screw the slip nuts.

If the pipes are short, then Purchase a longer pipe of the correct diameter. Now place it similarly as described above.

And In case you require to bend the pipe, buy a rotating P-trap. Or an Outlet tee can also be tried. Now Line it up. If you use an extension pipe, you’ll only need to bend it.

Step 11

Again, apply some silicone sealant at the perimeter of the sink.

Step 12

Now reconnect all the power lines and turn on the shut-off valves. Also, observe the flow and any leakage.

Final Word

Installing a new kitchen sink can be fun if you have the right tool to do that. Don’t compromise your safety as you have to deal with some delicate materials.

How to Wrap a Knife Handle?

Wandering how you can ensure maximum durability of your knife as the handle sometimes come off? Looking for a way to make grip even firmer? Then look no further because this article will answer all your questions.

Ever try to wrap your knife handle to better use? If not then it’s time to do so.

Wrapping your knife handle will give you a more firm grip on the knife. It will also make your knife stress resistant for longer. You will get a new look for your knife as a bonus.

So let’s dig into the process.

Materials required:

  • Knife;
  • Leather;
  • Para-cord;
  • Scissor;
  • Tape;
  • Lighter.

Wrap with a leather string:

Wrapping the knife with a leather string can be a little hard. But it will provide more durability and an elegant look.

Ready the string:

First, cut the leather into a strip with your desired width. Keep the length at least four or five times your knife handle. Now soak the strip into the water until it becomes soft.

Start wrapping:

After the leather is soft enough to work with, tape it at the starting of the handle underneath to the blade. Now start rotating the string around the handle covering the taped portion. Put enough pressure to make the wrapping tight. Keep rotating the string until you reach the end. Make sure there is no gap between the wraps.

Put tape at the sharp end of the blade for safety.

Secure with a knot:

When you reach the end, place a knot to secure your loops. Make the knot tight enough to give you the firmness. You can be a little creative in making the knot.

Final touch:

Trim the excess leather. Finally, dry the leather before you use the knife.

Wrapping with a para-cord:

Wrapping the knife handle with Para-cord is easier than the leather string. It will also provide you more flexibility while knotting.

Basic wrapping:

You can simply use the basic rotating style for the Para-cord as well.

  • Tape one end of the cord on the handle. Start wrapping the cord from the other end. Make the rotations as tight as possible. Each time the loop will go covering the taped cord. Keep rotating until you reach the end and cover all of the previously tapes cord.
  • When you reach the end, make a simple knot with the previous cord end.
  • Cut the excess Para-cord and secure the knot.

Cross knot:

It’s time to think out of the box. Rather than going with a traditional rotational wrap, you can go for a cross knot to give your knife a stylish look.

Weave the knot:

  • To make this type of knot, first cut a long string of the Para-cord. Then place the middle of the cord underneath the handle starting.
  • Grab the right end and place it over the handle so that it goes under the left end. Now take the left end and loop it over the right end. This will make a cross pattern on the handle.
  • Now grab the right end and make a loop from underneath the handle up to the front of the handle. This will go over the left end.
  • Now again take the left end and make a loop on the right end.
  • Repeat the process while making a cross pattern until you reach the end.
  • At the end make a knot and secure the wrap properly.
  • Get rid of the excess cord.

You can try any other knot of your choice as well. Don’t forget to secure the end of the cord by holding a lighter at the end for a while. The flame will seal the cut off edges of the cord.

Final thoughts:

Wrapping your knife will ensure firmer grip as well as durability of your knife. As we use a knife very frequently in our daily chores, the handle sometimes comes off. Wrapping the handle properly will prevent this incident.

Make sure to dry the handle properly after every wash.

It will also make the daily hard chopping more enjoyable and faster. Your hand will love it as wrapping the knife handle will ensure less stress on the hands.

How to Install a Kitchen Backsplash?

Want to update your kitchen? Adding a tile backsplash to your kitchen wall will surely serve this purpose quite well. In fact, it makes the boring cooking work lively. Next, the question comes is that what type of tile you will choose. Well, there are several options. For example, you can go for peel-and-stick tile or mosaics for easy installation. Whatever you may choose, the installation process isn’t something very easy.

To make it easy to understand, we’ve divided the whole procedure into three parts. In each part, we described the process step by step.


  • Tiles
  • TSP
  • Level
  • Unsanded white grout
  • Grout Boost and Grout float
  • Tile mortar (porcelain)
  • Grouting sponge
  • Tile trim
  • Notched tile trowel of ceramic
  • Spacer and
  • Tile cutter

Part 1: preparing the wall

Preparing the wall means making sure that the wall is clean and dry.

Step 1

First, turn off all the power sources in your kitchen. Now remove the switch plates in there’s any. Also, tape off the junction of the countertop and the wall, cabinet, and outlets. For better safety, remove the stove too.

Step 2

Now apply ledger board which is a sturdy piece of lumber. It works as a temporary support to the tiles until the cure of the adhesive. In addition to this, It also keeps the tiles level at the place with no countertop. Now Use a level to attach the ledger board.

Step 3

Now it’s time to clean the wall. First, Mix trisodium phosphate (TSP) with water and gently clean the wall. And you must follow the manufacturer’s instruction. Again, you can also use soft detergent afterward.

Step 4

Now observe the wall flatness of the wall. Then Fill the dips and ripples if the depth is more than 1/16 inch. Then Let the wall dry fully.

Part 2: planning the tile layout

You must provide a 1/8 inch gap at the junction of the cabinet and countertops.

Step 1

First, Point the center of the wall and draw a vertical line.

Step 2

Now lay the tiles horizontally along the wall. Then Check the ends with the help of spacers. If the tiles are too narrow, then you need to adjust the pattern.

Step 3

Now you have to check the vertical layout.

First, find the lowest point of the countertop by using a level. Now hold a tile at that place. As mentioned above, keep an expansion gap of 1/8 inch. Now draw a line at the top with a level and then extend it throughout the area of work. So this line will work as the cutting guide.

Finally, make a jury stick to find where the tile ends at the top. Then Use tile sand spacer board to line a straight board.

Part 3: attaching the tile

This includes a lot of mixing and attaching work. So you must follow the manufacturer’s guide.

Step 1

First, Mix the adhesive that you’ve chosen and follow the directions. Now spread it on the wall at a small section as these adhesives dry quickly. Use a drywall trowel. Now using a notched trowel comb over it. But don’t cover the reference line with adhesive.

Step 2

Now press the tile with a twist. Again, keep the required 1/8 inch expansion gap. Then Use a rubber float and press it against the tile to set the adhesive.

Step 3

Now complete tiling the wall progressing toward each small section. Then Look whether the spacing is even or not. If you need to cut the extended edge of a tile, then use a tile cutter.

Step 4

Now feel the expansion gap using the unsanded grout.

First, spread the grout diagonally with a rubber float. Then Wait for about 10 minutes. Now use a sponge in the diagonal motion to wipe away extra grout as Diagonal motion protects the grout line. Also, don’t forget to rinse the sponge time to time. But don’t wipe the grout from the joints. Always apply light pressure.

Step 5

Now, wait for some time until the grout dries. Then spread grout sealer. Now fill the 1/8 inch expansion gap with silicone sealant or caulk.

Step 6

Finally, reset all the switches and outlets and check whether they adjust to the new set of tiles. Also, connect the stove and turn on the power.

Final verdict

The success of installation largely depends on the right choice of materials. As you can see, it involves many delicate substances. So always be careful of safety issues. If you are not an expert, then it’s wise to work with someone who is experienced.

How to Connect Soundbar to TV with Optical Cable?

Hold on!

Before getting down to the main point, let’s talk about the benefits of using optical cable.

Usually soundbars use HDMI connection. This option is admired by every user for its outstanding performance for both audio and video signals. So, when optical cable is being chosen over HDMI, it’s normal that the decision won’t be taken positively by many users.

While HDMI is already giving you what you want, why go any other way? Why go for optical cable?

Yes, we admit that HDMI is excellent and most probably one of the most beneficial technologies of modern science. However, you should always be open to other options and try new things to detect the one that’s more convenient for you. You never know, maybe optical cable was the best thing for you all along?

Also, the time is evolving and so is the technology. Considering various sides, manufacturers are leaning towards optical cable a little more and trying to come up with something better. Sure, it still hasn’t succeeded to take the place of glorious HDMI cable, but this cable is still doing its best in this field and that’s praiseworthy.

Many latest soundbar models are featuring optical cable connection along with HDMI/RCA and you may consider using it this once keeping a few things in mind.

Why HDMI Is Preferred by Everybody

We have to learn the function of HDMI before recognizing optical cable’s benefits, in order to understand the reason behind HDMI’s popularity properly. Soundbar is used for improvising TV audio/home theater experience.

For good performance, audio and video signals are required to be transferred simultaneously. HDMI works with dedication for the following action. Instead of using separate cables for A/O and V/O, you can accomplish the task using a single cable through HDMI.

Moreover, this cable is specifically designed for complying with Dolby Digital Sound tech which makes it a more preferential choice for home theater. Besides, it also functions quite wonderfully with Blu-ray, which works as another reason for the popular demand.

Benefits of Optical Cable

Sure, HDMI gives a pleasant TV watching experience and that’s why soundbars still use this as the primary connectivity option. However, optical cable comes with its own benefits which should be checked out too.

What is the fastest transition medium?


And optical cable uses light for transitioning signal. So, you can imagine the fast motion that goes inside! Again, this is the reason why optical cable is used for establishing network everywhere.

The optical cable transfers audio signal in the pace of light, which works like magic for home theater system. It takes the signal from the source and sends it to the receiver. The receiver combines all signals in one package and distributes them among the drivers at the same time. Briefly put, it shortens the signal transmitting process for the soundbar.

If your soundbar doesn’t include a system higher than 5.1 channel, you can use optical cable for connection. It’s capable of distributing signals fairly in systems below 5.1 system. So, you may consider connecting your soundbar to tv with optical cable if it doesn’t contain more drivers than a 5.1 channel system.

How to Connect

Step 1. Turn the power off

This step must be followed almost every time you’re trying to establish a connection between two electronic items. Electric signal isn’t safe for human body after a certain amount. When you’re working with an active connection, chances of you getting electrocuted increases in an alarming way.

So, turn off the TV, soundbar and every other device connected with the system before beginning the process.

Step 2. Remove plastic protectors

You’ll see, the optical cable and the soundbar’s optical cable port are protected with plastic casing. It’s actually done for user’s safety, but you need to remove the casing for work. Get rid of the plastic and proceed ahead.

Step 3. Connect TV and soundbar

Now, here comes the main part: connection.

Take the optical cable. You will see there’s a port situated on the soundbar’s rear part. This port is included for optical cable and it’s labeled as IN port. (There will be a port with OUT label as well, that mustn’t be used for this connection)

On the back of your digital tv, you’ll also see two similar ports (IN and OUT). We’re gonna use the tv’s OUT port.

Link one end of the cable with soundbar’s IN port and other end with tv’s OUT port. Remember, the cable should directly connect tv and soundbar only. If you’re planning to add speakers or console, connect them to the TV using HDMI.

Step 4. Turn the power on and check connection

Once the soundbar and the tv is connected, turn the power on and test the performance. Adjust properly in case it’s not working.

How to Replace a Single Handle Kitchen Faucet?

Can you think of a complete kitchen without a kitchen faucet?

Well, to get an easy water supply installing a faucet in your kitchen sink is necessary. However, you may need to repair or replace your sink faucet because of leakages in the faucet or in the supply line. It is a little tricky when you want to replace it with an old damaged kitchen sink faucet.

There are a few types of kitchen faucets are available in the market. Most often people use the single handle kitchen faucet in their kitchen. Installing and replacing a single handle kitchen faucet is easy and quick. So, if you are also replacing a single handle kitchen faucet, you have stepped in the right place. Here, in this primer, I’ve discussed the steps of how to replace a single handle kitchen faucet. So, let’s have a look.

Basic Steps On Replacing a Single Handle Kitchen Faucet

Step 1: Switch Off both cold and hot water line

Before beginning, shut off the water lines. The cutoff valves are usually located underneath the sink. In the rare case, they can be found in some other places like a utility shed also. Turn the valves in the clockwise direction and shut them off.

If you want to be sure you can keep the on for sometimes when you are turning the valve. If it has been a long time that you removed those valves, be very gentle while you turn.

Step 2: Turn on the existing kitchen faucet

After turning off the hot and cold-water lines, turn on the faucet which you are going to remove. By this way, the pressure in the water supply lines will release. Besides, it lets you check that whether the pipes are turned off or not.

Step 3: Detach the old faucet

Remove the nuts that keep the faucet connected to the sink. Locate and unscrew them. These nuts are often placed beneath the kitchen sink.

If the nuts are on the upper side of the sink, you have to remove the handle and deck plates. By removing them, you can access where the nuts are and unscrew them.

Step 3: Clean the sink area

After disconnecting the mounting nuts, lift out the old single handle kitchen faucet. Now, using an adjustable wrench remove the sprayer hose from the assembly. Then, lift out the disconnected sprayer hose.

Using a scouring pad, clean the sink area properly. If the escutcheon cap of the sprayer hose remains in good shape, you can reuse it. If not, replace the cap with the escutcheon cap of the new single handle kitchen faucet. Remove all the grim and putty. Also, clean the mold and rust and make sure that the new fixture is free from all the problems.

Step 4: Place the new deck plate

If the new faucet has a rubber or plastic gasket, place it on the proper holes in the sink. Again, if the faucet has no gasket or a putty plate, use plumber’s putty beneath the rim of the deck plate.

Place the string of plumber’s putty in the groove and press it lightly to settle it in its place.

Step 5: Position the new sprayer hose

Now, place the new sprayer hose. Slip down it through the sprayer hole and feed up it through the center of the faucet hole. Then, connect the hose to the sprayer nipple using an adjustable wrench.

And now it’s time to place the new faucet with the water supply lines. Read the manufacturer’s instructions to set the new faucet’s fitting into the assembly. Position it in the right place and then crawl back beneath the sink to adjust the new connections. Finally, connect the supply lines to the shut-off valves.

Step 6: Set up the new faucet

At this stage, you have to insert and feed the supply lines and the connectors into the center hole of the faucet. Make sure that the gasket of the faucet is in the right position. Now seat the new faucet.

Then, install the washer and nut under from the beneath of the sink to the end bolts. These bolts hold the faucet in its place.  Lastly, tighten the nuts using a basin wrench.

Final Thoughts

Replacing a single handle kitchen faucet is one of the basic plumbing tasks. By following the guidelines properly, you can do this task easily. Besides, hiring a plumber for replacing a faucet is expensive. So, why costing so much when you can simply do it by yourself? Also, replacing the kitchen faucet yourself, you can ensure a proper replacement. So, save your money from going down the drain. I hope, this article will be a complete guideline for you as a beginner.

How to Replace a Kitchen Sink Faucet?

Can you think how uncomfortable it will be working in your kitchen without a kitchen sink faucet? With a damaged kitchen sink faucet, you can’t work with easiness in your kitchen. Besides, there will be a huge wastage of water due to the leak in the faucet. So, you better replace the faucet with a new kitchen sink faucet. Thinking how can you replace a kitchen sink faucet?

Well, you may hire a plumber to get the task done. But, hiring a plumber for replacing a kitchen sink faucet is a little expensive. Moreover, if you know the process you can do it on your own. Replacing a faucet in the kitchen sink is one of the easiest plumbing tasks. Also, you can make sure yourself that it’s the water that only goes down the drain, not your money. Well, let’s start with the steps on how to replace a kitchen sink faucet?

How to replace a kitchen sink faucet?

Step 1: Remove the supply lines

At first, turn off the water. Secondly, remove the supply lines from the old kitchen sink faucet with care. Now, check whether your sink has shut-off valves or not. If they have, make sure that they are workable. Later, shut off and turn on the valves in order to check the activity of hot and cold water faucet.

Usually, the supply lines which are made of stainless steel are free from rupture. So, you should give this kind of supply line a try. To remove the supply lines, use a basin wrench. While removing them some water may come out from lines. So, keep a basket or jar to keep the replacing area dry. It’s recommended to remove old chrome plated lines as they may create corrosion.

Step 2: Remove the old kitchen sink faucet

Unscrew the bolts of your old sink faucet by a screw. The bolts hold up the faucet tightly in its place. So, you can’t unscrew them empty-handed. Now, remove them from their place. You have to also remove the locking nut and soap container.

Step 3: Replace the new kitchen sink faucet

Sometimes the sprayer attachment of your new faucet may differ from the old one. It is hard to fit the new faucet with the sprayer attachment. So, by using a screw loosen it and remove it. Now, check the number of holes under your kitchen sink. It’s very important to know as the replacement of kitchen sink faucet depends on how many holes are present. If the old sink faucet has 3 or 4 holes, you can replace it with a new one which has just one hole. It is not possible to fit a kitchen sink faucet with 3 or 4 holes in a one-hole kitchen sink system.

Use a rubber gasket or a plastic gasket over the holes. Otherwise, cover up the holes using plumber’s putty. It’s not important if there are one or four holes. Important thing is, to place the gasket in the correct position. Now, thread the screws into the threaded ring. Stop when they are one-fourth inch away from the sink. Then fit a washer beneath the sink. Besides, thread locking nuts under the sink by a screw. Make sure to screw the soap container tightly. Connect a hose to the supply pipe. Thus, you can move it with ease. Pull down the weight on the hose and join the ends. After that, attach nuts using a screw. Finally, connect the hot and cold water supply lines. Be sure that they don’t interfere with the hose line.

Step 4: Turn on the supply lines

Finally, turn the supply lines on. Before that, make sure the faucet is off. Check if there is any leak in the kitchen sink faucet and in the supply line. Now. check for leakages keeping the faucet active. In case you found any leak, evaluate the steps you’ve completed. Be sure that all the steps were executed perfectly. Plumbers tape. If there are still leakages, contact an experienced plumber for better guidance. When no leaks are found, replacing the kitchen sink faucet is finished.

Final Thoughts

I hope, you’ve already realized that replacing a kitchen sink faucet is no big deal. If you follow the steps properly, you can replace a new kitchen faucet easily. So, why wasting money calling a plumber when you can do it by yourself? Hope, this article will be a proper guideline for you.

How to Fix a Leaking Kitchen Faucet?

We all are more or less spending plenty of our times in kitchen. But out of all these utensils and items, what is the thing you use most in a kitchen? The faucet in your kitchen is probably the answer.

Because of the pressure, it goes through daily, it may prone to some problems. Think about the joints. A leaky or malfunctioning joint can damage the entire faucet system.

Now the question is, how to fix it.

Starting- The general process

Step 1: First, Twist the handles clockwise to turn off the shut-off valves under the sink. Two things can take place in this case. Wither you can’t find any valves, and otherwise, you can find one stuck. Shut off the main supply in case of the second situation.

Step 2: Now, to relieve the remaining water from the line, turn on the faucet handle smoothly. Then cover the drain with a towel or sink plug to small parts from dropping down into the hole.

Determining which type of faucet you have

There are generally four types of faucets.

  • Compression faucet- it can easily be recognized by sight as it has two handles. One for hot and another for cold water supply.
  • Ball faucet- it contains a ball bearing
  • Cartridge faucet- it has a cartridge whose materials vary from the faucet to faucet. The handles often contain a decorative cap.
  • Ceramic disk faucet- consists of a ceramic cylinder.

The last three types have only one swiveling arm at the center to supply both hot and cold water as required. You can’t differentiate them by sight. You can only recognize them by disassembling them and observing the internal mechanism.

How to fix a compression faucet?

Step1: Remove each of the handles

First, remove the decorative cap, if any. Now, remove the screw and then the handle.

Step 2: Remove the nut

Use a wrench to remove it. There is a stem underneath.

Step 3: Expose the seat washer

Take off the stem. You’ll find a thinner circular O-ring that sits on a thicker rubber-made thing. It’s called seat washer.

Step 4: Replace the parts

Find the cause of leaking the faucet.

If you see the handles are leaking, then you need to change the O-ring. It’s wise to use the same brand of old parts. So take it to the hardware shop to find the brand.

If your faucet is dripping, you’ll find the seat washer worn out. You must find a new one of the exact size as seat washers vary in size. Before installing it, coat the new part in the plumber’s grease.

Step 5: Reassemble the parts

Finally, replace all the parts in the reverse sequence.

How to fix a ball faucet?

Step 1: Purchase a replacement kit

You don’t need to replace the whole faucet but only a few parts. So go to a home repair shop and look at the plumbing section. This replacement kit comes with all the necessary parts and the tools required to fix this.

Step 2: Unscrew and remove the handle

Unlike the compression faucet, first, lift the handle off.

Step 3: Remove the collar and the cap

Use pliers to do this. Also, remove the cam with the tool provided in your replacement kit, washer, and the ball. Unlike the ‘ball and socket’ joint, usually, a white color rubber ball corks the socket. The movement of this ball controls the release of the water.

Step 4: Take out the inlet seal and springs and replace

Use needle-nosed pliers to accomplish this. Now, cut off the old O-ring with a knife. Install a new one after coating it in the plumber’s grease. Then again, install the new seals, springs and cam washer in the reverse sequence.

How to fix a cartridge faucet?

Step 1: Unscrew and remove the handle

Remove the screw first and then tilt the handle backward. Now pull it. If necessary, pry off the cap.

Step 2: Pull the cartridge

Pull it to make it stand up straight. There’s a circular, plastic threaded piece called retaining clip. It sometimes causes trouble by holding the cartridge in its place. So pull it out with pliers if necessary.

Step 3: Locate the faucet spout and the O-ring

Remove both of them. Then reassemble the handle.

How to fix a ceramic disc faucet?

Step 1: Remove the handle and escutcheon cap

First, unscrew the handle. You’ll see the escutcheon (usually metal) lying directly under the handle.

Step 2: Remove the disk cylinder and seals

As you unscrew and remove the cylinder, it’ll expose several seal underside it. Seals are usually made of neoprene. Now, pry them out. If these look Frayed, pitted, worn or thin, for the sake of safety, replace them. So take them to the hardware store so to find the exact match.

Step 3: Clean the cylinders

Use white vinegar especially in case of hard water. Soak the cylinders in the vinegar and wait for some hours for complete build-up. Then consider them for reuse.

Step 4: Finally, Reassemble the handle

Then Turn the water on.

Note: water shouldn’t be run too forcefully. Therefore, turn it slowly. Otherwise, the ceramic disk may crack.

Final verdict

See, fixing a leaky faucet is nothing daunting. Now, collect the tools, identify the leakage and just get down to work!

How To Change A Bathroom Faucet?

The latest faucet is excellent to renew your bathroom and present it a brand new look. Whether you need to change an old or broken faucet, this is a comparatively simple project that you can fulfill within a short time. Just you have to pick the best ones and to attach them correctly. However, the advantages of a new faucet are so impressive that is exceed your hesitance. Follow certain steps to install an amazing new bathtub faucet thyself. Stay tuned!

Collect your tools and supplies

Changing a bathroom faucet is a sincere job, and it does require some tools that you’ll need to remove the old faucet and place the new one. The tools you’ll add:

  • Basin wrench
  • Adjustable wrench
  • Torch
  • Wiper
  • Measuring strip
  • Bucket
  • Plumber’s strip
  • Bathroom cleanser or saponin
  • Sponge
  • Additional cloth
  • New faucet

Turn off the water

Locate the water shutoff plug for the bath sink. It should be following the sink, inside the compact. Turn the plug on the right to close and shut off the water connection to the faucet. If you have difficulty locating the shutoff plug, you can turn off the water supply to the whole line.

Leave everything from under the sink. Place a napkin below the tubes to protect the compact from water decay. Place a container over the towel and below the faucet to catch excess water that drops down. You can also place a refuse bag down under the wiper for even more assurance. This will protect your vanity, tub, and tiles from drops and water loss, and prevent water from sprinkling everywhere when you push the faucet.

Remove the Old Faucet

Use a flexible wrench to release the nuts and unthread them. Convert them to the port side to loosen them. Now, release the nuts and the parts from the tailpieces. Once you have removed the nuts, parts, and supply chains, the faucet will be free automatically. Pick the faucet in both hands and remove it exact out from the holes. Remove the extra hole if there is any problem away with the faucet.

Choose the right faucet

When you have removed the old faucet, you can count out what hole shape you are going with and the kind of faucet you want. There are three important kinds of faucets:

  • Single hole– where the sink has one hole, and the faucet will all be one simple item of a single holder.
  • Center-set– there will be three holes in the tub and the one-piece tap will have distinct handles supervising the warm and cool water.
  • Split-set- which go with three-hole sinks, but the spray and two holders come in three distinct pieces.

Place the gasket

The gasket is a plastic piece that sets sink to ensure a right seal and stop losses. Fit the gasket up to the underside of the faucet and balance the holes properly. If your faucet didn’t work with the gasket, you need to see the company’s guidelines before you set the faucet.

Embed a new faucet

Pick the faucet and carefully inserted it into the holes. Match the pipelines and valves with the right holes, and set the faucet into position. When the faucet is in the holes, turn on the nuts to tighten. When you have tightened by hand, finish tightening them with the adjustable wrench if needed. Don`t try to tighten the nuts several further, it may damage the sink.

In Finally, you can attach the water line as well. Attach all water connection to the faucet, and then tighten the nut once again. If you find a leak, check the connection one more time and try it resolving. After that, turn on the water taps, when water is running, recheck the leaks. In that time, you can wait for five to ten minutes. If everything seems perfect, you are done.

How to Install a Bathroom Vanity?

The latest bath vanity can append style to your bath interior and also give more storage and shelf space. You’ll be glad to know installing them is reasonably easier than you imagine. We’ll guide you everything how you can install a bathroom vanity, including where to place it and how to ensure it to the wall. You’ll also get how to cut pockets for your pipes with a hole saw. Just read this article till the end.

Place the vanity

At first, you have to set the vanity in point and sketch on the wall. Now use a studding finder to position the studs and mark. Sometimes dual vanities need more space and pipes difficulties when installing. On that note, follow the manufacturer’s guidance for details. It also appreciable when you want to install a bath vanity with the cap.

Prepare for Vanity Installing

You guys should`ve to follow three important steps to install a vanity. See the below:

Mark Holes

Now, consider the height of the top of the vanity corner cabinet on the back wall. Its no dimension is actual, just beat the actual cabinet and apply that dimension. But keep a distance from the floor to the top of the bottom cabinet. And, use a standard position to easily mark this height wherever the vanity is being placed.


When the height is signed off, set the vanity into the right position and locate the bottom cabinet so that the vanity top has the same overhang on both sides. To get a right position, use a box level to make sure vanity is horizontally level. If required use woodcutter to level the vanity.


Now you have done the basic pre-condition to install a vanity. So time to fasten the vanity install the wall. You can use two drywall screws into the back panel and studs. If you want a corner installation, the second screw can use the wall stud and another screw can use through the back.

Connecting the Gap inside the Wall

With the vanity installations, you may have seemed some gap in the wall. Try to resolve it as soon as possible, otherwise, your wall might be damaged that is ugly to see. You know ceramic tile base wall or floor break down easily while hole. The solution is using a wood filler tape to close this gap and also important what`s your wall perfectly need by an engineer.

Performing the Filler Strip

To making the filer stripe, pay attention to the below tricks:

  • Slice Filler Strip to Shape and length
  • Cut a slice of wood at concise ½” high to the length from the height of the vanity.
  • Trim it to the amplitude of the hole.
  • If you have a rounded hole base tile, use a little gauge and press it into the hole
  • Exchange the shape of the wood filler strip by following it with a pencil.
  • Transfer the shape to the wood liner strip by tracing it with a pointer.
  • Test fit the liner strip and modify as important.
  • When the liner strip is resolved accurately, try to complete the wood strip to coordinate the base bureau as nearly.
  • Connect the filler strip with paste or little brads.It just requires being held in a set.

Installed Vanity Base

While your vanity is attached to the wall and the liner strip is placed the vanity will be in the position shown. The vanity is now available in the cabinets and fitting of the sink. On that note, you have to follow the next steps. That all are:

  • The next step is to join the vanity lid
  • Ensure the vanity lid is now in the last position you want.
  • Use a dot of silicone caulk in a bent pattern of the backsplash.
  • Allow the caulk restorative 24 hours.
  • If you use a limestone vanity cover, use a marble sealer before applying the vanity.

Hello guys, We guess your vanity is completely installed take some steps and use your hard work! You have done a fabulous job and increase your home’s condition. Now clean your hands!

How to Replace a Kitchen Sink?

What is the most obvious element of your kitchen? Well, the kitchen sink is the most used stuff in your kitchen. You couldn’t think a single day even a few hours without a sink. Whatever you want to wash of kitchen you will definitely think of sink and no other. And if your sink somehow got leaked or stained then you have to replace it urgently.

You can do this stuff by yourself. If you do not have much time to call a mechanic, or do not want to waste money on this then you can easily do this job. The whole procedure of replacing a sink is here for you. Hope you will be the beneficiary from here!

How to replace a kitchen sink

There are few parts and steps you need to follow while replacing a kitchen sink. Those are given here below:

Disconnecting supply:

  1. First, you need to look under the sink for shutting off the hot and cold water valves. If you do not find there, then look in the basement. But if there is nothing in the basement, then use main water line to shut off.
  2. Then remove the remaining water by turning on the faucet.
  3. Keep a bucket under the line because there may be some water remaining.
  4. To disconnect the supply lines, use a wrench as the lines are fastened together.
  5. You can turn off the power supply by flipping the circuit breaker. It will be on the lowest floor of the residence. Then pull the unit’s plug.
  6. There may have metal fittings in the pipes. Therefore, use a pair of pliers to loosen them. Then pull the pipes and keep them aside.
  7. Dishwater drain hose is in the bottom of the sink which connects with a pipe. Use pliers and loosen the fasteners, then pull the hose. After finding the bracket, use a screwdriver to loosen it and then pull it off.

Replacing top mounted sink:

  1. There are small metal clamps outside of the sink. Depending on the size of the clips, use wrench or screwdriver. Loosen them for rotating the clamps.
  2. There is caulk between sink’s rim and countertop. At this time, you need a knife. Hold a knife against the countertop so the is as flat against it. From freeing the sink, carefully cut all around the sink.
  3. After this push up the underside of the sink and keep it aside. Then check that if there is any caulk left on the countertop. Wash it with soap and water and then dry for the new one.
  4. Where you need to place the new sink place it, if it doesn’t fit then you need to adjust it. If your sink is larger, then you can cut away a part of the counter top. But for the smaller one, you need to exchange it from the market.
  5. In order to seal the sink, use caulk all around the sink. And then place the new one in the sinkhole.
  6. The fastens you have opened, attach again all around the sink. Twist the screws with screwdriver or wrench. And then it will be secure.

Replacing under mount sink:

  1. Select a piece which is longer than the sink and place it over the counter top.
  2. Use this to secure one end of the sink. Drop the other end of sink through the drain and tight it.
  3. Use the putty knife for cutting caulk.
  4. Use screwdriver or wrench to loosen the clips as before.
  5. Then put caulk around the new one and place it properly.
  6. Put all the sink clips.

Reconnecting supply:

  1. Reset the faucet lines and hold each line properly.
  2. Roll some putty and place around strainer rim for sealing it.
  3. By tightening washers and nuts, secure the drain and remove extra putty.
  4. The water supply line you have removed before reattach it.
  5. Install dishwasher pipe and connect all the pipes.
  6. Turning on the water supply test your sink.

Final verdict

The full procedure of replacing of the sink is here. So now you don’t need to look for any other people as you can do this job very well! If something happens with your sink that you have to replace it, try it yourself and enjoy your work as well as a new sink!

What is a santoku knife used for?

You are buying new kitchen stuff for your kitchen and when you are thinking which knife will be better for you. Those knives which you can use for cutting any vegetable or meat or something else is the best option for you. Well, as you are thinking over this you can undoubtedly choose santoku knife. It is not too large in size so you can easily handle this when working in your kitchen.

So you may want to know exactly what its use then stay here with me as I am going to discuss this here!

What is a Santoku knife?

The first thing that comes to your mind is what type of knife it is and what it looks like. Basically, the santoku is a Japanese word so it’s clear that its origin is in Japan and made for Japanese homemakers. It came from the word ‘sahn-toh-koo’. The knife is especially for some delicate work and also professional chefs can also use this. It’s especially known for its light weight and finely balancing. Some chefs prefer this knife highly for cutting vegetable or meat.

It is similar to the traditional chef’s knife. The difference may be it is thinner than chef’s knife in thickness, smaller in length, and a gradual curve at the end. Stainless steel is the main element of this knife so it may be expensive.

What Santoku knife is used for?

The Santoku knife has two sizes. The smaller size is similar to a utility knife and the larger one is similar to chef’s knife. The smaller one can be of 5″ and you can use this for medium cutting works in the kitchen. The Larger one has standard blade size. But sometimes it may become difficult for cutting with the larger one because of the width of the blade. If you need to cut fast you can use the smaller one because larger one reduces the cutting speed as well as consistency.

Cutting vegetable, fish, boneless meat, fruit is easier because of its wide blade as it makes cutting consistent. When you are cutting large size vegetables then using the less weight knife is better as it causes less fatigue with respect to the heavier knife. Blade profile of it is straight and the thickness of the blade is same so you can maintain the cutting thickness of fruit or vegetable.

The blade of the Santoku knife is of the same width. Rather than a pointy end, it has a squared end. Also, the blade is uniformly wide which is great for cutting cylindrically shaped vegetables. You can also use this for cutting fruit, fish or poultry. It is the best for the home cook and daily use. So you can choose this for your kitchen without any doubt.

The Granton style blade is for keeping the vegetable or fruit particles from knife blade so do not stick with the blade. This also helps you to achieve easier as well as faster motion. When you need to slice any of the foods fine or narrow, you can use Santoku knife as the blade thickness of it is less. For decoration of the plate, the slices will be suitable enough and enhance the look of the table. You can chop boneless meat with this knife.

So you can see for household kitchen works Santoku knife is easier to operate, effective and sometimes obvious.

Final verdict

If you are new with kitchen stuff, then knowing about various things is necessary. As the knife is an obvious element of the kitchen so you better know much about it. From here you come to know precisely about Santoku knife and its use. So hopefully it’s going to help you a lot. Again even though you are not new in this but facing problems in the kitchen in chopping then it’s going to help you. Santoku knives are not too large so especially women can operate this very easily and feel it’s necessary.

What is a serrated knife used for?

Are you someone who enjoys cooking? Trying to sort out the perfect knife for cutting those crusty bread? Then you are in the right place.

Choosing the right knife for the right job is an important task in the kitchen. So you will need some knowledge before jumping into it.

What is a serrated knife:

A serrated knife has a blade with tooth-like edges. It is mainly used for cutting foods that have a softer inner part with a harder and crusty outer surface. They are sometimes called bread knife as well.

Serrated knives are mostly used by chefs .but is thinner than a chef’s knife.

There are different teeth pattern for serrated knives nowadays. They have different thickness and different degree of sharpness. The narrower the knife, the neat it will make the slice. A good serrated knife will require less force and hence it will not cause any stress for your hand as well.

Benefits of a Serrated knife:

The main function of a serrated knife is to cut through the crusty surface smoothly. So that can avoid crushing the food and making crumbs. As the teeth are edged, they rip through the hard surface of the food neatly. These knives are ideal for the cases when you need less force to slice the food.

When to use :

There are many foods for which serrated knives are preferable than plan chef’s knives. Mostly for food with a crusty exterior and juicy interior.


The main use of a serrated knife is to cut bread. As the saw-type teeth of these knives create less friction with the food surface, they cut through them neatly. This prevents the bread from crushing and scattering crumbs everywhere.

Slashing the loaves:

For baking the loaves properly, slashes are made on the upper surface of them. So to make it cleaner and precise, serrated knives are the best choice.

Cutting the dough:

Serrated knives are also very handy when it comes to cutting the cake’s dough.

Juicy tomatoes:

If you are seeing a hard time cutting tomatoes with the plane knife, then you should switch to a serrated knife. Serrated knives cut through the hard surface of tomatoes and then smoothly glide down through the juicy part. These make the cut so precise and neat. You can make the slices as thin as you want with these knives.


Want to cut your chocolate into small pieces but it breaks every time you try? Why not try a serrated knife then?

The sharp edge of a serrated knife is also helpful in cutting chocolate bars very well.

Layered cake:

Layered cakes are so soft. So cutting them with a plane knife maybe a bad idea as they will imply mush force on the cake. A serrated knife can be your best companion for cutting the layered cake as they are so delicate.


Melons have a pretty hard outer surface which is tough to cut with a plane knife. Try to cut it with a serrated knife and you will never go back to your plane knife again.

Fruits with tough skin but chewy interior like peaches can be cut neatly with this knife as well.

Sharpening, cleaning and storing:

Sharpness is the main factor when it comes to making a neat cut. But with time serrated knives get dull. You can use a file or sharping tool to sharpen it.

Cleaning the knife properly is also important. Cleaning the knife will regular dishwasher will make it dull. So try to clean it with a sponge or hand with soapy water. Don’t leave the knife in water for long.

Store it in a safe and airtight place. Rub it with a napkin to dry it before you put it into the storage box.

Final thoughts:

Having a serrated knife can be very handy sometimes. If you want the bread or cake to be precisely cut then there is no alternative but a serrated knife. It will give you that store like perfection.

Invest in a good knife. Keep it clean and store it well. This way it will last a long time.